Ridder RW140 Скачать руководство пользователя страница 2

Страница: 2 / 52

TABLE OF CONTENTS

1. GUIDELINES, STANDARDS AND CONDITIONS

1.1 Applicable guidelines and standards

1.2 Approved personnel

1.3 Warning about discouraged use

1.4 Warranty provisions

2. SAFETY, PRECAUTIONS AND SYMBOLS

2.1 Signal words, instructions and warnings

2.2 Precautions and safety instructions

2.3 Residual risks

2.4 Symbols and abbreviations

3. PRODUCT DETAILS

3.5 Technical specifications

4. INSTALL INSTRUCTIONS

4.1 Special tools and equipment

4.2 Mounting positions

4.3 Sprockets

4.4 Installation

4.5 Installation options A–F for output shafts

4.5.1 Basic output shafts (BOS)

4.5.2 Special output-shafts (D, LD, LK ....)

4.5.3 Installation chain (for A–D)

4.6 TRA drive-unit onto RW45\240TRA motor gearbox

4.7 Belt drum onto RW45\240/400L motor gearbox

4.8 Cable drum onto RW45\240/400L motor gearbox

5. CONNECT INSTRUCTIONS

5.1 Removal covers

5.2 Electrical material

5.3 Protection - Conditions and starting points

5.4 Tightening-torque motor-connections

5.5 Control-circuit connection - 3-wire [RLS]

5.6 Motor-current connection - 3-wire [RLS]

5.7 Control-circuit connection - 5-wire [RSU]

5.8 Control-circuit connection - 5-wire, Alternative [RSU]

5.9 Change Direction-of-rotation - Switching sense

5.10 OPTIONAL - Position Feedback

6. USER INSTRUCTIONS

6.1 Usage - Conditions and starting points

6.2 Direction-of-rotation RW motor-gearboxes

6.3 Operation

6.4 Safety functions and stop functions

7. COMMISSIONING INSTRUCTIONS

7.1 Commissioning - Conditions and starting points

7.2 RLS/RSU limit-switch system

7.3 Adjusting the end positions

7.4 Installation covers

8. MAINTENANCE INSTRUCTIONS

8.1 Maintenance

9. SERVICE

9.1 Troubleshooting

9.2 Technical support

10. ENVIRONMENT

10.1 Decommissioning and removal

10.2 Waste disposal

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Содержание RW140





















































Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды

Ridder RW140, Руководство по эксплуатации продукта

Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды