Ridder RW140 Скачать руководство пользователя страница 8

Страница: 8 / 52

3. PRODUCT DETAILS

3.1 Identification

This product manual is only applicable to:

•

Ridder Motor Gearboxes RW 1-phase

•

Serial numbers from 200.900.000

•

Item numbers from 500000.

Identification is possible from the sticker on the location shown. Refer to the explanation that

follows on how to read the information. For more information on item numbers and models refer to

the Ridder catalog or website at

ridder.com

EXAMPLE

COVERS

= If not applicable: No symbol in identification.

NOTE:

Possibly the sequence of symbols is different and/or other symbols are included in the identification. Not all symbols

and assembled configurations (such as LK, LD, ...) are included in the explanation.

K = Sprocket in an assembled configuration.

WI: White color finish

z16: Optional sprockets

Alternatives: z12/3z16 (3x for D model)

IP55: Protection rating

No symbol in identification = IP54

Alternatives: 11/18/22/25/30/37/44/55/66/110/130

1: 1-phase mains voltage

115: Mains voltage [V]

09: Motor power at 50\60 Hz [daW]

86: Limit-switch range motor-gearbox

L: Model with winch shaft

45 = Torque 120, 90 or 60 Nm

Alternatives: 70/140/400/600/800

RW: General designation Ridder RW motor-gearboxes

CU: CSA/UL certification mark

Alternatives: 3C (CCC)/C (CSA)/U (UL)

Alternatives: 55/97/120/860

60: Mains frequency [Hz]

No symbol in identification = 50 Hz

Alternatives: 230

TRA: Model for built-on rack unit

D: Model with continuous worm-shaft

No symbol in identification = Sprockets (K)*

1: Rotational speed of drive shaft at 50(60) Hz [rpm]

Alternatives: 2/3/5/34(41)

240: Torque [Nm]

P: Thermal-Overload Protection-Switch (PTO)

V: Grease lubrication

No symbol in identification = Oil lubrication

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Содержание RW140





















































Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды

Ridder RW140, Руководство по эксплуатации продукта

Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды