Ridder RW140 Скачать руководство пользователя страница 14

Страница: 14 / 52

Electrical

RW series

RW45

RW240–600

RW800

RW70/140

Duty cycle [kb]

Applicable for intermittent duty, duty class s3-35%, with a

maximum running time of 25 minutes.

Maximum current

Refer to the nameplate of the electric motor.

Power

Thermal protection EM

[°C (°F)]

3-wire electric motors are thermally protected with a PTO switch

with a switching temperature of 140 °C (284 °F).

Cable glands

M16x1.5 mm/M20x1.5 mm. Also refer to §5.2.

Mains voltage

115 V - 60 Hz

•

•*

230 V - 50 Hz

240 V - 60 Hz

•

* Not applicable:

RW600

Ambient

RW series

RW45

RW240–600

RW800

RW70/140

Protection rating

IP54*

Ambient temperature [°C (°F)]

0–60 °C (32–140 °F)

* IP55 only applicable if in identification.

4. INSTALL INSTRUCTIONS

Installation is only permitted to approved personnel.

Do a check of the supplied parts in the table that follows. Use these parts with the mounting plate

(selection) which is applicable. Refer to §4.4.

Parts list *

00000

Motor Gearbox RW 1-phase **

* Minimum parts list: Motor gearbox

without

optional parts and accessories.

** Motor gearboxes have spring washers and bolts M10x20 (2x), M10x25 (3x) or M12x25 (4x). Item numbers

from 500000.

Installation (general)

•

This product manual gives

only

information about the installation of RW motor-gearboxes and

related connections to output-shafts (installation options).

•

Information about the different operated systems is

not

(or not fully) given or gives only general

information.

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Содержание RW140





















































Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды

Ridder RW140, Руководство по эксплуатации продукта

Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды