Ridder RW140 Скачать руководство пользователя страница 46

Страница: 46 / 52

•

Do steps 1 thru 4 again to adjust the opposite end position (A or B).

•

Go to step 6 if the two end positions are adjusted.

•

The procedure to adjust the limit-switch system is completed.

7.4 Installation covers

Always put the covers (2x) and the bolts (2x4 [or 1x4 + 1x3]) back after the work.

Problems

with

moisture

and/or the

protection rating (if applicable) must be

prevented!

•

Do a check of the gaskets (2x) for dirt and damages.

•

Put gaskets (if removed) back carefully and make sure that no damage is caused.

•

Tighten the bolts crosswise and gradually with the correct tightening torque (2x4 [or 1x4 + 1x3]).

In this manual shown illustrations can be different than the components and/or systems.

Do a functional check of the limit-switch system after the two end

positions are adjusted.

Do not go across adjusted end positions when the motor gearbox

is operated manually or with electric tools (externally with the

hexagon socket in the electric-motor shaft).

This prevents damage to the limit-switch system and an incorrect

functional operation.

PH/PZ - 0.5 Nm (4x)

PH2 - 1.5 Nm (4x)

Plastic cover *

TX\SLOT (3x) - 1.0 Nm

* Alternatives: Metal cover

PH/(PZ) (4x) - 1.0 Nm

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Содержание RW140





















































Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды

Ridder RW140, Руководство по эксплуатации продукта

Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды