Ridder RW140 Скачать руководство пользователя страница 18

Страница: 18 / 52

4.3 Sprockets

•

Usually

Ridder installs sprockets onto the

two basic output shafts (BOS)

of most models (general

designation: RW).

•

Some models (such as RW-LK, RW-D, RW-LD) have:

•

One

special output-shaft (

) plus

one

basic output shaft (

BOS

)

•

One

special output-shaft (

) plus

two

basic output shafts (

BOS

)

•

Two

special output-shafts (

L + D

). (The

-shaft is for installation of a drum.).

•

Some models or shafts (BOS and/or special shafts) are supplied without sprockets.

Thus it is possibly necessary, if applicable for the configuration, to:
❶ Install necessary (optional) sprockets on output shafts or

❷ Interchange sprockets with necessary (optional) sprockets on output shafts.
Refer to the illustration (step ❶ and ❷) that follows for the configuration of shaft keys (a, b),

retaining rings (c) and ring (d).
For more information on item numbers and models refer to the Ridder catalog or website at

ridder.com

* Shaft

-model: Installation of a drum is also possible. Refer to §4.7/4.8.

** Shaft

-model is for installation of a drum. Refer to §4.7/4.8.

Basic output shafts [BOS]

Output shaft LK

Output shaft D

HEX 3 mm

M6 x 8 mm

Model: RW

Model: RW-LK

Model

2x BOS

1x Shaft-LK*

+ 1x BOS

RW-D:

1x Shaft-D

+ 2x BOS

RW-LD:

1x Shaft-D

+ 1x Shaft-[L]

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Содержание RW140





















































Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды

Ridder RW140, Руководство по эксплуатации продукта

Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды