Ridder RW140 Скачать руководство пользователя страница 4

Страница: 4 / 52

2. SAFETY, PRECAUTIONS AND SYMBOLS

2.1 Signal words, instructions and warnings

Signal words (ISO 3864-2)

This product manual contains safety instructions with different signal words. The list that follows

gives the risk levels and possible effects of each signal word.

Instructions and warnings on the product

Read the product manual to fully know all product

properties, before it is used or work starts!

COVERS

It is not permitted to use high-pressure cleaners (and

related cleaning agents)! Use a soft brush with a small

quantity of water without cleaning agents.

Warning - Electrical voltage

After installation interchange the plug in the highest

position with the vent plug! Refer to the permitted

mounting positions in the product manual.*

Not applicable to motor gearboxes filled with grease!

Suggestion to perform an operation more effectively.

May result in damage or problems if an action is performed

incorrectly.

May result in minor injury if the hazard is not avoided.

Significant injury, possible death, if the hazard is not avoided.

Severe injury and possible death if the hazard is not avoided.

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Содержание RW140





















































Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды

Ridder RW140, Руководство по эксплуатации продукта

Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды