Ridder RW140 Скачать руководство пользователя страница 25

Страница: 25 / 52

4.6 TRA drive-unit onto RW45\240TRA motor gearbox

Installation options G, H, I

Type A mounting plate installed between the motor gearbox and the TRA drive-unit.

Refer to §4.4: “Optional mounting plates”, step ❶A.

Do the

steps ❶, ❷ + ❸, ❹, ❺

of the

two illustrations

that follow.

Foot mounting or top mounting of the on the motor gearbox installed TRA drive-unit.

Do the

steps ❶, ❷ + ❹, ❺ + ❻

❼

of the

two illustrations

that follow.

Wall mounting with the special wall mounting plate (417910/417953) of the on the motor gearbox

installed TRA drive-unit.

Do the

steps ❶, ❷ + ❹, ❺, ❽, ❾

of the

two illustrations

that follow.

Preparing components (G, H and I)

❶ Install the shaft key (d), the pinion (e) and the retaining ring (f) onto the output shaft.

❷ Put the rack (g) through the TRA rack drive-unit.

Installation option G

Note:

Possibly there is no mounting plate installed to the structure at this time. Install a (type A)

mounting plate or an alternative to the structure first.

Refer to §4.4: “Optional mounting plates”, step ❶A.

❸ Put the (type A) mounting plate (h) or an alternative between the gearbox and the TRA drive-

unit.

❹ Install the TRA rack drive-unit onto the gearbox (and mounting plate or alternative [h]) with the

special M10 bolts ([i] 599015/599016).

❺ Tighten the bolts (i) gradually with the correct tightening torque. Refer to

SID/SBI

information.

Installation option H

❹ Install the TRA rack drive-unit onto the gearbox with the special M10 bolts ([i] 599015/599016).

❺ Tighten the bolts (i) gradually with the correct tightening torque. Refer to

SID/SBI

information.

❻

❼ Drill two holes of Ø13mm for foot mounting (j) or top mounting (k) in the structure. Use

M12 fasteners (l or m) to install the TRA system onto the structure. Obey the instructions

for installation of M12 fasteners (l or m).

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Содержание RW140





















































Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды

Ridder RW140, Руководство по эксплуатации продукта

Результаты поиска

Содержание RW140

Отзывы:

Похожие инструкции для RW140

Бренды по названию

Популярные бренды