background image

Sloped building-structure

• 

If the building structure is sloped Ridder recommends to put the tube motor and guiding system 

at the highest position. This makes sure that water can flow away from the tube motor along the 

roller screen when it is winded up.

Assembly order

• 

In the manual an assembly order is given. A different order can be used, but you must obey the 

guidelines in this manual.

ALTERNATIVES
Replacement - Guiding unit: P20 to VK10 (tube motor 550032/550039)

• 

The replacement (VK10) for the P20 guiding unit.

• 

There is a special guiding unit for the two installation sides of the roller screen.

Tube motor 550037: Adapter VK10 to P20

• 

The 550037 is a tube motor (VK10) with an adapter set 550411. The head of the tube motor is 

changed to P20.

• 

The tube motor is attached to the guiding unit (P20) with hex socket-screws M4 and a locking 

plate.

• 

There is a special guiding unit for the two installation sides of the roller screen.

550032

550039

P20

4.2.3

VK10

4.2.4

P20

550037

550411

Ridder Drive Systems

T

 +31 (0)341 416 854 

F

 +31 (0)341 416 611 

I

 www.ridder.com

11

Содержание RB50EPLUS





































Отзывы: