Ricoh A095 Скачать руководство пользователя | Manualshive

Страница: 81 / 680

background image

1.6 DEVELOPMENT UNIT

1. Be careful not to nick or scratch the development roller sleeves.

2. Place the development unit on a sheet of paper after removing it from the

copier. This prevents any small metal objects (staples, clips, E-rings,
etc.) from being attracted to the development roller and getting inside the
unit.

3. Be careful not to bend terminals on the rear side.

4. Clean the drive gears after removing the used developer.

5. Never load different types of developer or toner into the development

unit. Doing so will cause poor copy image and toner scattering inside the
copier.

6. Developer initial setting is necessary when new developer is loaded.

Do not perform the developer initial setting with used developer.
Do not make any copy before initial setting.

7. When removing the development unit, push it to the right to prevent the

OPC drum from being scratched by part of the development unit.

8. The doctor gap and the development rollers position must not be

adjusted in the field as they are precisely adjusted at the factory using
special tools. Do not loosen any screws with white paint.

9. Before pulling out the development unit, disconnect two connectors.

10. When inserting out the development unit, do not pull the knob.

11. When setting the development unit in the machine, do not forget to

replace the two connectors.

1.7 TRANSFER BELT UNIT

1. Do not touch the transfer belt with oily bare hands.

2. When servicing the transfer belt cleaning unit, be careful not to damage

the edge of the cleaning blade.

3. Apply setting powder or toner to the new cleaning blade.

1.8 CLEANING SECTION

1. When serviceing the cleaning section, be careful not to damage the edge

of the cleaning blade.

2. Do not touch the cleaning brush with vare hands.

3. Before disassembling the cleaning section, place a sheet of paper under

it to catch any toner falling from the section.

A095/A096/A097

4-4

FSM

«
...
79
80
81
82
83
...
»

Содержание A095









































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A095

Documax A6300 Series

Бренд: DataSouth Страницы: 180

VersaLink C405/N

Бренд: Xerox Страницы: 256

Бренд: Cycjet Страницы: 26

5550B - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 117

WorkCentre 3345

Бренд: Xerox Страницы: 18

Бренд: Xiamen Hanin Electronic Technology Страницы: 62

Бренд: Printek Страницы: 34

WorkCentre XD Series

Бренд: Xerox Страницы: 63

Magicolor 4650DN

Бренд: Konica Minolta Страницы: 260

Бренд: Konica Minolta Страницы: 12

EuroLine Series

Бренд: Output Technology Страницы: 73

Бренд: Konica Minolta Страницы: 3

Бренд: AstroJet Страницы: 32

apeosport-v c5585

Бренд: Fuji Xerox Страницы: 493

Бренд: Intermec Страницы: 2

Бренд: SATO Страницы: 255

KYOCERA FS-C8100DN

Бренд: Kyocera Страницы: 12

DocuPrint 96 IPS Series

Бренд: Xerox Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды