manualshive.com logo in svg

Ricoh A095, Руководство по обслуживанию

Поделиться
Скачать
Ricoh A095 Скачать руководство пользователя страница 310

1.5

OPTICS THERMISTOR

SC190 - Optics thermistor open

Definition: [level: D]
The optics thermistor is open.

Possible causes:

•

Optics thermistor open

NOTE: When the optics thermistor is shorted, no SC code is indicated.

The exhaust fan rotates quickly and continuously.

SC191 - Scanner motor thermistor open

Definition: [level: D]
The scanner motor thermistor is open.

Possible causes:

•

Scanner drive motor defective

NOTE: The scanner motor thermister is within the scanner motor.

1.6

MAIN CHARGE

SC302 - Charge corona leakage

Definition: [level: D]
The charge power pack detects a charge corona leakage (output: 0V) for 4.8
msec, or detects the output to be more than 7 kV, 10 times in one job.

Possible causes:

•

Main charge corona unit defective

•

Main charge power pack defective

•

High voltage control board defective

SC303 - Charge corona wire cleaner failure

Definition: [level: C]
The current of the charge corona wire cleaner drive motor is over the
specified current within 4 seconds after the cleaner motor starts.
The charge corona wire cleaner does not move back to the end block within
30 seconds.

Possible causes:

•

Charge corona wire cleaner drive motor defective

•

Insufficient lubrication for the charge corona wire cleaner drive
mechanism (G501 grease)

•

High voltage control board defective

T

rou

bl

e

-

sh

o

o

ti

n

g

FSM

6-7

A095/A096/A097

Содержание A095









































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды