Ricoh A095 Скачать руководство пользователя страница 182

Страница: 182 / 680

24. Turn on the main switch and perform the scanner free run for about 5

minutes to break in the wires and to confirm correct scanner movement
as follows:

- Scanner Free Run -

1. Remove the air inlet duct [A] (1 screw).

2. Remove CN502, CN503, CN504 from the optic control Board [B].

3. Short-circuit TP514 and TP504(GND) on the optics control Board.

4. Turn on the main switch.

5. Short-circuit TP512 and TP504(GND), then the machine

automatically starts the scanner free run.

6. Turn off the main switch.

25. After performing the scanner free run, check the second scanner

alignment, then the first scanner alignment.

26. Perform the scanner control adjustment. (Refer to Scanner Control

Adjustment.)

27. Check the copy image.

[A]

[B]

TP514

TP512

TP504

Rep

lacemen

t &

just

ment

FSM

5-31

A095/A096/A097

Содержание A095









































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание A095

Отзывы:

Бренды по названию

Популярные бренды

Ricoh A095, Руководство по обслуживанию

Результаты поиска

Содержание A095

Отзывы:

Бренды по названию

Популярные бренды