RichAuto AutoNow F1 Series Скачать руководство пользователя страница 2

Страница: 2 / 67

北京锐志天宏科技股份有限公司

Beijing RichAuto S&T Co., Ltd.

Forging ahead, create future together!

Thank you for choosing RichAuto products!

This manual helps you be familiar with the company's products, and get information

about systems‟ components,configuration etc.

This manual contains detailed knowledge of the system characteristics,operating procedures, installation

&commissioning, and safety precautions. Please read this manual carefully before using the system and

machine, which will help you to use it better.

Cautions:

1. It‟s strictly prohibited in the strong interference and strong magnetic field environment. Operating

ambient temperature:0-70

℃

;Environment humidity: 0-90% (non-condensing).

2. Insert U disk in the correct direction. Do not pull out or insert 50-pin signal transmission cable when

system is powered on.

3. During the perform processing in U disk file, do not pull out the U disk to prevent the interruption of

data transmission.

4. Strictly prohibited metal, dust, and other conductive substances drop into the handheld controller shell.

5. The machine casing shall be well grounded to ensure work safety and prevent interference.

6. Unauthorized removal is strictly prohibited, no internal user repairable parts.

7. For long time not using, please power off and keep it properly.

8. Be careful to prevent it from water, dust, fire when using.

9. Do not use the corrosive chemical solvents to clean the device.

10. Spindle motor bearing life and its speed is inversely proportional.

11. The tool bit is very sharp. Do not touch when it is running, in order to avoid injury; Do not use

handkerchiefs, scarves to approach it to prevent embroiled damage.

Important statement:

The Company shall not be responsible for any loss caused by improper using or failure to comply with the

rules of operation.

Beijing RichAuto S&T Co., Ltd owns final interpretation of this manual, we reserves the rights to revise all

information in this manual, including data, technical details, etc.

Содержание AutoNow F1 Series




































































Результаты поиска

Содержание AutoNow F1 Series

Отзывы:

Похожие инструкции для AutoNow F1 Series

Бренды по названию

Популярные бренды

RichAuto AutoNow F1 Series, Руководство пользователя

Результаты поиска

Содержание AutoNow F1 Series

Отзывы:

Похожие инструкции для AutoNow F1 Series

Бренды по названию

Популярные бренды