manualshive.com logo in svg

RFL Electronics GARD 8000, Инструкция по эксплуатации

Поделиться
Скачать
RFL Electronics GARD 8000 Скачать руководство пользователя страница 257

Commissioning 
 

GARD 8000 Distance Relay 

 

RFL Electronics Inc. 

 

 
 

6.

 

All Voltage and Current levels should be zero if the external current and voltage sources are not 
applied.  

7.

 

Connect a Power System Simulator, apply current or voltage, refresh the screen and verify the 
metering values. 

 

 

12.9

 

INPUT/OUTPUT MAPPING VERIFICATION 

 

•

 

The physical Inputs and Outputs are mapped on the “System Logic Configuration” web page.  
Any available hardware input or output can be freely assigned to any logical input or output 
that is available in the Input or Output mapping block (please use the GARD logic drawing as a 
reference).  Verify which current logical inputs and outputs are mapped to the hardware inputs 
and outputs using the web pages. Additional logical inputs or outputs could be mapped in the 
Input Mapping and Output Mapping Logic blocks located in the Distance Relay Logic Design.   

 

1.

 

At the “Home” web page click on “Settings” and select “System Logic Configuration.” 

2.

 

Click on “Input Mapping” and verify all Input Mapping.

 

 

March 1, 2009 

12-7 

973.334.3100 

Содержание GARD 8000















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды