manualshive.com logo in svg

RFL Electronics GARD 8000, Инструкция по эксплуатации

Поделиться
Скачать
RFL Electronics GARD 8000 Скачать руководство пользователя страница 126

Description of Operation 
 

GARD 8000 Distance Relay 

 

RFL Electronics Inc. 

Carrier Receive

Forward pilot zone

Three Poles Open

Power swing block

Block pilot trip

Weak infeed trip

distance

Zone 1 Fault

100ms

0

Enable open breaker

carrier send

0

T

Dist carrier send

extend time

Enable Distance

pilot scheme

power swing block

Distance pilot
protection trip

Distance

protection channel

start

 

Figure 9-14. PUTT 

 

An open circuit breaker carrier send signal selection is included in the settings, ‘Enable open breaker 
carrier send’. To determine if the three poles have opened, three status contact inputs (one for each 
pole) can be used, or one input can be used that corresponds to the three poles in series. 
 
The “Dist carrier send extend time’ provides a minimum time for channel signal transmission. Channel 
tripping and channel sending can be disabled using the status contact input ‘Block pilot trip’. It can 
also be disabled for power swing conditions by adjusting the Power swing Element ‘Distance pilot 
scheme power swing block’ setting. 
 
In case weak infeed logic is to be used with the PUTT scheme, the setting should be ‘TRIP+ECHO’. 
The ‘Echo’ setting is of no use for an underreach scheme and the ‘Trip+ECHO’ setting allows for local 
trip, even though no echo function will be performed (as the sending end has already tripped from its 
sending, underreach zone). 
 

9.2.4

 

DIRECT TRANSFER TRIP 

 

This scheme is similar to Permissive Underreach Transfer Trip (PUTT) with the difference that 
channel signal reception produces instantaneous tripping without additional supervision. The carrier 
receive signal is provided with a pick-up delay to prevent tripping for spurious carrier signals, set on 
timer ‘Security Time’. Carrier send (Distance protection channel start) can be initiated by an open 
breaker as selected by the setting ‘Enable open breaker carrier send’. Power swing can be set to block 
carrier send by the setting ‘Distance pilot scheme power swing block’ and both trip and carrier send 
are blocked by the signal input ‘Block pilot trip’. 
 

August 1, 2009 

9-18 

973.334.3100 

Содержание GARD 8000















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды