Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 94

Страница: 94 / 110

Now tip the printer to the left side near the edge of the table and at-

tach the weight to the part of the toothed belt for the Y-direction that is

now at the bottom using the cord.
For the extruder carriage to stay at the top as illustrated, simply bind

the toothed belt together with a cable tie (see circle in the right im-

age).
The weight must be suspended so that it can move freely. The string

may touch the side part on top.

Measure the distance between the two toothed belt halves as illus-

trated. Set a distance of 25 mm with the belt tensioner (measured at

the outside of the toothed belt).

Tip the printer onto its back close to the edge of the table and remove

the bottom sheet. Attach the weight in the middle to the part of the

toothed belt for the Z-direction that is now at the top with the cord.
The weight must be suspended to be freely movable but may touch

the mains unit housing. This is not a problem.

Measure the distance between the two toothed belt halves as illus-

trated. Set a distance of 41 mm with the belt tensioner (measured at

the outside of the toothed belt).

25 mm

41 mm

Содержание RF2000 v2 BSS















































































































Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды