Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 78

Страница: 78 / 110

• Click the tab "

Manual Control

" on top.

• In the field "

G-Code

", enter "

M3013

" (without the quotation marks)

and click the button "

Send

The command "

M3013

" outputs the values of the matrix in steps. If

you use the command "

M3013 P1

" instead, the values are output

in mm.

• The log field now shows the values of the matrix.
• The first series of numbers (;7;0;20;40;...) indicates the position of

the value in the X-direction in mm, with 7 representing the format

of the matrix and not being relevant for the position in X- and Y-

directions.

• The position in the Y-direction is also indicated in mm by the figures

at the beginning of each row of figures (;0;30;50;...).

• Also observe that the value (-772) at the upper left, i.e. in position

X=0 and Y=0, is located at the front left of the printing plate when

looking at the printer from the front left. The value (-628) at the

lower right, in position X=170 and Y=290, is at the rear right on the

heating plate.

• The offset value indicated under the full values (larger, red box), in

dicates the lowest value. This then is the position where the nozzle

has the smallest distance from the printing plate. In our example,

the offset value is -588 steps.

• Now find the offset value in your matrix. In our example, the -588

steps are in position X 160 and Y 250. You need to set the nozzle

to 0.3 mm in this position in the next heat bed scan.

• To the right, you can see the matrix again, presented a little better

structured. The Z-offset value -588 is bolded here.

• The values in the matrix can be briefly explained as follows:

The values are indicated in steps. 2560 steps in Z-direction equal

precisely 1 mm. The values indicate the distance between the sur-

face of the heating plate and the trigger point of the Z-limit switch

"Z-Min" (Z home position).

This means that in position X 160 and Y 250, the distance between

the heating plate and the Z Home position is 588 steps.

• If everything is set correctly mechanically, the values in the matrix

must all be negative.

front left

front right

20 40 60 80 100 120 140 160 170

-772 -808 -836 -832 -860 -872 -888 -916 -964 -964

-832 -876 -896 -892 -920 -932 -936 -952 -980 -980

-920 -964 -988 -972 -980 -980 -972 -956 -984 -984

-948 -968 -996 -988 -988 -984 -980 -964 -980 -980

110

-976 -996 -1012 -992 -972 -968 -964 -960 -964 -964

130

-928 -956 -976 -952 -956 -964 -960 -964 -968 -968

150

-912 -928 -916 -892 -908 -904 -892 -900 -900 -900

170

-896 -888 -880 -868 -860 -844 -824 -828 -808 -808

190

-860 -872 -868 -820 -812 -796 -752 -756 -740 -740

210

-888 -884 -872 -824 -796 -744 -704 -696 -672 -672

230

-936 -944 -944 -852 -792 -752 -700 -676 -656 -656

250

-952 -940 -928 -836 -788 -724 -664 -636

-588

-588

270 -1120 -1084 -1028 -936 -868 -800 -736 -668 -628 -628

290 -1120 -1084 -1028 -936 -868 -800 -736 -668 -628 -628

back left

back right

Содержание RF2000 v2 BSS















































































































Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды