Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 37

Страница: 37 / 110

When the temperatures have been reached, the printer will wait for 10

minutes to ensure that the extruder and the printing plate are heated

through entirely. The waiting time is displayed in seconds in the status

bar.

Then the heat bed scan starts automatically.

Aligning the two extruders

After the measurement has been performed, the printing plate and

the extruder unit return to their home positions and then immediately

move to the middle of the printing plate.

The display shows "

Align Extruders

This means that the second extruder must be aligned now.

The extruder 0 should now be supported nearly entirely on the print-

ing plate.

To be certain, first release the holding screw of the left extruder (ex

truder 0), so that it is actually supported on the printing plate.
Then release the screw of the right extruder (extruder 1) and lower it

carefully onto the printing plate.
Now tighten the two screws again in sequence. Best hold the extruder

at the very top of the inlet. This prevents them from twisting and hitting

the fan sheet. Both extruders must be applied to the printing plate with

the same force.
Press the button "

Play

" (6) to terminate Heat Bed Scan.

Attention! Never touch the hot extruder or the printing plate dur-

ing the settings! There is a danger of burns!

Attention! Always stay near the printer while printing.

This applies specifically in this place, since the printer

is waiting for your action and input. The firmware has

a safety deactivation integrated that cancels the pro-

cess after 60 minutes, but the extruders should only

be kept at temperature for the time needed without fil

ament.

Printers with a single extruder do not require alignment of

the two extruders, of course. After a successful head bed

scan, the distance between the nozzle and printing plate is

determined automatically here. The process therefore

continues seamlessly without any action on your part.

Содержание RF2000 v2 BSS















































































































Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды