manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Поделиться
Скачать
Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 14

14

11. First commissioning

a) Overview of the first steps

The following overview shows the first, important steps with the RF2000 v2. This is a brief summary of the subsequent chapters until your first 

print with the printer.

•  Completion of initial commissioning.

  Some important things are explained to you here that you should do in any case after transport and unpacking. The chapter "Initial Commis-

sioning" also contains important notes on correct setup of the printer and, of course, correct connection, incl. important safety notes.

•  Download of the software/firmware package.
  We regularly provide new versions of the download package on our website. It contains the current firmware and software as well as current 

printing examples.

•  Update of the firmware of the printer.
  Before you continue, always check the firmware version of your printer first and update the firmware if necessary. Errors are frequently re

-

moved here and new functions may be installed.

•  Familiarise yourself with the general operation of the printer.

  Before you are able to sensibly use the printer, become familiar with its operation. We will not only introduce operation via the key pad to you, 

but also briefly explain the menu of the printer.

•  Execution of the calibration.
  Calibration (basic setting of the Z-limit switch; setting of the extruders, execution of a printing plate scan) is one of the most important subjects 

of the operating instructions. Only if you have correctly performed calibration will you also achieve a good printout.

•  First insertion of the filament.
  We will explain to you how you can insert or exchange or replace the filament correctly and what must be observed in this.
•  Your first print of an example object from the SD Card.
  We will lead you to your first printout step by step using an example from the enclosed SD card. Also observe our notes at the end of the 

chapter after printing out and the general notes in the chapter below.

 

Before you start initial commissioning, all transport protections or fuses that have been installed during installation or for 

transport must be removed. 

 The finished device (single and dual extruder) has blue crepe adhesive tape stuck to the printing plate in the factory. This improves 

adhesion of the printed object. This special blue adhesive tape can be re-ordered at our shop under Conrad order no. 1093104.

 

The printer also has a test printout enclosed that was produced in the scope of production. 

 

If the motors are moved manually, the display may light up. This is not a malfunction. A voltage induced by the movement in the mo-

tors causes the display to light up.

Содержание RF2000 v2 BSS















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды