manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Поделиться
Скачать
Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 60

60

e) Print

The printing file produced in this manner can be printed now. There are two options for this:
•  Save the printing file on an SD card to print out stand-alone. For this, click "

Save to File

" (1). This saves the file as *.gcode and must be set 

at the same time when you save the file from the G-code editor (disc icon). The precise content of the G-code will be saved into the file here.

•  The second possibility is to send the file directly to the connected 3D printer via the USB interface of the computer and print it. 
•  Before you start printing in single mode, however, check which extruder is active. This is irrelevant for dual mode. For this, click the tab 

"

Manual control

" (2).  In the drop down menu (3) (first figure on the next page) there, you can select the desired extruder to use for the 

printout.

 

Extruder 1 (in the software/Manual control) = extruder 0 (at the printer and in the G-code) = the left one from the front view

  Extruder 2 (in the software/Manual control) = extruder 1 (at the printer and in the G-code) = the right one from the front view

•  Click "

Print Preview

" and then the button "

Print

" (4), to start the printout.

•  While printing, the log window (5) (first figure on the next page) shows current information on software, slicer and printer.

1

2

4

Содержание RF2000 v2 BSS















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды