Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 45

Страница: 45 / 110

The filament is now inserted.

Push the direction button "

left

" 2 x to return to the main menu.

Important!

For the right extruder, always choose “

Extruder 1

” as

the active one. Then you can also perform insertion with the function

Load Filament

c) Removing and changing the filament

Hold the filament when it moves out of the extruder. Otherwise, it may jump out and cause injury. The upper layers of the

respective filament roll may jump open as well, which may cause the filament to tangle.

Removing the filament

Remove the filament according to the same procedure as used for insertion. However, instead of "

Load Filament

", choose "

Unload Filament

in the menu "

Extruder

The active extruder is heated up automatically. Then the filament is removed from the extruder after a short waiting period.

Of course, you can do this manually. For this, use the button "

Filament feed -

" (4) after the extruder is heated up.

Changing the filament

Proceed in the same manner when changing the filament. Remove the filament ("

Unload Filament

") and then insert the new filament ("

Load

Filament

").

If you perform this process manually, you can insert the new filament at once after removal.

No matter if you use the function "

Load Filament

" or insert the filament with the infeed buttons, always observe that the outflow of

the filament from the nozzle and the press-on pressure of the ball bearing holder must be the same in both extruders.

Содержание RF2000 v2 BSS















































































































Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды