manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Поделиться
Скачать
Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 31

31

c) Setting the distance between the nozzle and the printing plate

 

Only the left extruder (viewed from the front) (extruder 0) is used for calibration in the dual extruder. The distance between the nozzle 

and the heating plate must be set to 0.3 mm.

 

Important! Determine the position with the smallest distance between the nozzle and the heating plate in the cold condition. The basic 

setting of the upper Z-limit switch (Z-min.; light barrier) also takes place in the cold condition. This means that if the extruders or the 

printing plate have heated up before, you need to let them cool off entirely first!

 

The left extruder is set when hot!

 

If you have acquired a finished device, check whether the distance is between 0.8 mm and 1.0 mm when determining the 

highest position of the printing plate. If applicable, repeat the "basic setting of the upper Z-limit switch (Z-min.; light bar-

rier)" on the next page.

 

Attention! Never touch the hot extruder or the printing plate during the settings! There is a danger of burns!

Determining the position with the smallest distance

First move the printer Z-axis to its home position (

Home Z

). Briefly 

push the button 

OK

 (2) in the main display.

Use the direction buttons (1) to navigate to menu item "

Position

".

Push 

OK

.

Use the direction buttons to navigate to menu item "

Home Z

".

Push 

OK

, to move the printing plate to the Z-Home position.

 Attention! The extruders must not touch the printing 

plate during the subsequent setting. If this is the case, 

lower the Y-plate a little with the arrow button "down" 

(3) and turn out the actuation for the Z-stop a little.

Now determine the position on the printing plate where the distance 

between the nozzle of the left extruder and the printing plate is small-

est. For this, target the 9 positions that are marked at the top of the 

picture. For this, carefully move the extruder carriage and the printing 

plate by hand. It is easiest to determine the right position with a feeler 

gauge.

Leave the extruder carriage and the printing plate in the position 

where you have determined the smallest distance.

Содержание RF2000 v2 BSS















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды