manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Поделиться
Скачать
Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 5

5

3. Intended use

The 3D 

printer produces two-coloured 3D-objects from suitable printing files. For this, suitable raw material (filament) is melted in the two print 

heads and attached in the required position for the object.
This product is only approved for connection to 230 V/AC, 50 Hz alternating voltage.
It is intended for indoor operation only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be avoided under all circum-

stances.
Using the product for any other purposes than those described above may damage the product. Improper use also may cause dangers such 

as short circuit, fire, electric shock, etc. Read the operating instructions precisely and keep them. Only pass the product on to any third parties 

together with the operating instructions.
This product complies with the statutory national and European requirements. All company names and product names

 are trademarks of their 

respective owners. All rights reserved.

Arduino™ is a registered trade mark of Arduino S.r.l. and its affiliated companies.

 

ATTENTION Mains voltage - the connection, installation and wiring of the electrical components must only be performed 

by an electrician who is familiar with the applicable safety provisions. Before commissioning, inspection according to the 

applicable safety provisions must be performed by an electrician. This also applies to repair work.

 

Observe all safe

ty and assembly notes in these operating instructions and in the assembly instructions!

Current operating instructions

Download the current operating instructions via the link www.conrad.com/downloads or scan

the displayed QR code. Follow the instructions on the website.

Содержание RF2000 v2 BSS















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды