Renkforce RF2000 v2 BSS Скачать руководство пользователя страница 23

Страница: 23 / 110

d) The expanded main menu

The main menu contains the main display (see chapter "13. a) Description of the main menu") and 4 further views.

You can reach them via the direction buttons "

" and "

down

" (1). The displays are switched through in sequence. For example, if you push

the button "

down

" five times, the main display will be shown again.

1 x button "

down

" (1) pushed.

This shows the current positions of the individual axes.

2 x button "

down

" (1) pushed.

This overview shows the current temperature values (actual/target) of

the two extruders and the printing plate. The percentage at the very

right of each line shows the current heating output.

3 x button "

down

" (1) pushed.

This shows the entire printing time and the filament used up to now.

4 x button "

down

" (1) pushed.

This overview shows the current printing file at the top and the last

printed printing file at the bottom.

e) Menu overview

Operation takes place via the left key block at the printer:

• The direction buttons are used for navigation in the menu structure ("

left

" / "

right

" / "

down

• The button OK is used to confirm a selection in the menu and to call the menu structure from the main menu (description above under "13.

b) Function description of the operating buttons").

The menu structure may deviate slightly depending on firmware.

Quick Settings

Home all
RGB Light:

Off/White/Auto/Manual

Output Object
Speed Multiply:100%
Flow Multiply:100%
Preheat PLA
Preheat ABS
Cooldown
Disable Stepper
230V Output: Off/On
Restart

Restart now?

Yes

Содержание RF2000 v2 BSS















































































































Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды

Renkforce RF2000 v2 BSS, Руководство по эксплуатации

Результаты поиска

Содержание RF2000 v2 BSS

Отзывы:

Бренды по названию

Популярные бренды