manualshive.com logo in svg

Renesas SH7781, Руководство по оборудованию

Renesas SH7781 является высокопроизводительным процессором, предназначенным для широкого спектра приложений. На нашем сайте вы можете бесплатно скачать Руководство по аппаратному обеспечению для этого устройства. Получите всю необходимую информацию для работы с Renesas SH7781 на manualshive.com.

Поделиться
Скачать
background image

8.   Caches 

Rev.1.00  Jan. 10, 2008  Page 240 of 1658 
REJ09B0261-0100 

 

Physical address bits [4:0] are always fixed at 0 since burst transfer starts at a 32-byte 
boundary. 

 

8.7.4

 

Determination of SQ Access Exception 

Determination of an exception in a write to an SQ or transfer to external memory (PREF 
instruction) is performed as follows according to whether the MMU is enabled or disabled. If an 
exception occurs during a write to an SQ, the SQ contents before the write are retained. If an 
exception occurs in a data transfer from an SQ to external memory, the transfer to external 
memory will be aborted. 

•

 

When MMU is enabled (AT = 1 in MMUCR) 

Operation is in accordance with the address translation information recorded in the UTLB, and 
the SQMD bit in MMUCR. Write type exception judgment is performed for writes to the SQs, 
and read type exception judgment for transfer from the SQs to external memory (using a PREF 
instruction). As a result, a TLB miss exception or protection violation exception is generated 
as required. However, if SQ access is enabled in privileged mode only by the SQMD bit in 
MMUCR, an address error will occur even if address translation is successful in user mode. 

•

 

When MMU is disabled (AT = 0 in MMUCR) 

Operation is in accordance with the SQMD bit in MMUCR. 

0: Privileged/user mode access possible 

1: Privileged mode access possible 

If the SQ area is accessed in user mode when the SQMD bit in MMUCR is set to 1, an address 
error will occur. 

 

8.7.5

 

Reading from SQ 

In privileged mode in this LSI, reading the contents of the SQs may be performed by means of a 
load instruction for addresses H'FF00 1000 to H'FF00 103C in the P4 area. Only longword access 
is possible. 

[31:6] 

: H'FF00 1000 

Store queue specification 

[5] 

: 0/1 

0: SQ0 specification 
1: SQ1 specification 

[4:2] 

: LW specification 

Specifies longword position in SQ0/SQ1 

[1:0] 

: 00 

Fixed at 0 

 

Содержание SH7781





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7781

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Бренд: ABB Страницы: 44
EAW MX250 Owner'S Manual preview
MX250
Бренд: EAW Страницы: 10
Aaeon UP Squared 6000 Edge Computing Kit User Manual preview
UP Squared 6000 Edge Computing Kit
Бренд: Aaeon Страницы: 59
Patton electronics 1084 Installation And Operation Manual preview
1084
Бренд: Patton electronics Страницы: 16
Patton electronics NetLink 2960 RAS Datasheet preview
NetLink 2960 RAS
Бренд: Patton electronics Страницы: 2
TC Electronic ATAC Service Manual preview
ATAC
Бренд: TC Electronic Страницы: 55
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Бренд: 8e6 Technologies Страницы: 74
EMCIS LISN User'S Operating Manual preview
LISN
Бренд: EMCIS Страницы: 14
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Бренд: QNAP Страницы: 54
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Бренд: Supermicro Страницы: 54
Belden HIRESCHMANN IT MAMMUTHUS MTM8003-FAN User Manual preview
HIRESCHMANN IT MAMMUTHUS MTM8003-FAN
Бренд: Belden Страницы: 84
OWC Mercury FireWire 400 Owner'S Manual preview
Mercury FireWire 400
Бренд: OWC Страницы: 2
Lattice Semiconductor iCE40 SPRAM Series Technical Note preview
iCE40 SPRAM Series
Бренд: Lattice Semiconductor Страницы: 12
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Бренд: Intel Страницы: 105
MESA Electronic 4C24 Manual preview
4C24
Бренд: MESA Electronic Страницы: 27
SilverStone ECU06 Installation Manual preview
ECU06
Бренд: SilverStone Страницы: 17
ICP DAS USA PDS-734 Quick Start Manual preview
PDS-734
Бренд: ICP DAS USA Страницы: 8
Quantum MC300 Prism User Manual preview
MC300 Prism
Бренд: Quantum Страницы: 140

Бренды по названию

Популярные бренды

Загрузить еще бренды