manualshive.com logo in svg

Renesas SH7781, Руководство по оборудованию

Renesas SH7781 является высокопроизводительным процессором, предназначенным для широкого спектра приложений. На нашем сайте вы можете бесплатно скачать Руководство по аппаратному обеспечению для этого устройства. Получите всю необходимую информацию для работы с Renesas SH7781 на manualshive.com.

Поделиться
Скачать
background image

12.   DDR2-SDRAM Interface (DBSC2) 

Rev.1.00  Jan. 10, 2008  Page 516 of 1658 
REJ09B0261-0100 

 

12.5.3

 

Initialization Sequence 

The following shows an example of the initialization sequence. For detailed information such as 
the power supply and timing parameters, please refer to the datasheet for the DDR2-SDRAM 
being used. 

1.  Following the instructions in the datasheet guide for the SDRAM being used, supply the power 

and the reference voltage.  

2.  After the power-on reset has been canceled for the LSI and the CPU has begun operating, the 

system judges whether the LSI was in power supply backup mode or the normal initialization 
sequence (for information on entering settings in power backup mode, please refer to (2) 
Recovery from SDRAM Power Supply Backup Mode in section 12.5.10, DDR2-SDRAM 
Power Supply Backup Function). If it was an initialization sequence, the software is used to 
initiate a wait of at least 100 

μ

s. (An example of how to make the system wait for a specific 

interval such as 100 

μ

s can be found in section 12.5.11, Method for Securing Time Required 

for Initialization, Self-Refresh Cancellation, etc.) 

3.  Enter the settings for the SDRAM configuration setting register (DBCONF), the SDRAM 

timing register 0 (DBTR0), the SDRAM timing register 1 (DBTR1), and the SDRAM timing 
register 2 (DBTR2).  

4.  DLL settings are entered by writing them to the DDRPAD frequency setting register 

(DBFREQ).  

A.  Set DLLRST = 0.  

B.  Set the frequency of DDRPAD in the FREQ bit. 

C.  After DLLRST has been set to 1, the time interval of 100 

μ

s that the DLL needs in order to 

stabilize is applied through the software. The clock stabilization supply time of 200 

μ

s that 

is required for the DDR2-SDRAM to boot, including the wait time described in item 2 
above, can be assured. 

5.  Write the setting to the DDRPAD DIC, ODT, OCD setting register (DBDICODTOCD). The 

value written to the register should match the value set in EMRS(1) of the SDRAM.  

6.  Writing to the CMD bits in the SDRAM command control register (DBCMDCNT) sets the 

MCKE signal to the high level (H), and the software is used to have the system wait for at least 
400 ns.  

7.  Writing to the CMD bits in DBCMDCNT issues the PALL command.  

8.  Writing to the SDRAM mode setting register (DBMRCNT) issues the EMRS(2) command to 

the SDRAM. After that, the EMRS(3) command is issued.  

9.  Writing to DBMRCNT issues the EMRS(1) command to the SDRAM and sets various 

parameters in the EMRS(1) register in the DDR2-SDRAM. The values for DIC, ODT, and 
OCD should be set to match the DIC bit, ODT bit, and OCD bit settings in the DIC, ODT, 
OCD setting registers of DDRPAD.   

Содержание SH7781





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7781

Datasat AP20 Installation And Operating Manual preview
AP20
Бренд: Datasat Страницы: 32
Palo Alto Network M-200 Reference Manual preview
M-200
Бренд: Palo Alto Network Страницы: 56
Vivotek NR8401 User Manual preview
NR8401
Бренд: Vivotek Страницы: 136
Enterasys X-Pedition 2000 Getting Started Manual preview
X-Pedition 2000
Бренд: Enterasys Страницы: 86
3Com Token Ring Getting Started Manual preview
Token Ring
Бренд: 3Com Страницы: 18
Supermicro SC836 X9 User Manual preview
SC836 X9
Бренд: Supermicro Страницы: 24
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Бренд: Balluff Страницы: 12
Zoom 4412A User Manual preview
4412A
Бренд: Zoom Страницы: 48
B&B Electronics 4 Channel Input Buffer Board SDAIBB Product Manual preview
4 Channel Input Buffer Board SDAIBB
Бренд: B&B Electronics Страницы: 22
ZALMAN CNPS5X PERFORMA User Manual preview
CNPS5X PERFORMA
Бренд: ZALMAN Страницы: 8
Symantec SV1800 Series Safety And Regulatory Compliance Manual preview
SV1800 Series
Бренд: Symantec Страницы: 100
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Бренд: ivideon Страницы: 11
sound4 STREAM X Maintenance And Operation Instruction Manual preview
STREAM X
Бренд: sound4 Страницы: 66
MEN ME4 User Manual preview
ME4
Бренд: MEN Страницы: 48
SilverStone argon series User Manual preview
argon series
Бренд: SilverStone Страницы: 16
Intel Core 2 Duo E4300 Design Manual preview
Core 2 Duo E4300
Бренд: Intel Страницы: 55
National Instruments PXI Express PXIe-1085 Series User Manual preview
PXI Express PXIe-1085 Series
Бренд: National Instruments Страницы: 89
Ametek Land System 4 Landmark Technic Processor User Manual preview
System 4 Landmark Technic Processor
Бренд: Ametek Land Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды