REMS SSM 160 R, Руководство по эксплуатации, Страница: 9 / 68

GBR GBR
Article numbers SSM 160 R SSM 160 K SSM 250 K SSM 315 RF
Bench support SSG 280 250341
Steel case 251820
Protection cover 250243 250243 250343
Electric facing cutter 252100 252110 254100 255100
Facing cutter 252103 252103 254103 255103
Clamp right 252300 252400 254300 255300
Clamp left 252310 252410 254310 255310
Clamp insert set Dm 40 252320 252320
Clamp insert set Dm 50 252321 252321
Clamp insert set Dm 56 252322 252322
Clamp insert set Dm 63 252323 252323
Clamp insert set Dm 75 252324 252324 254320
Clamp insert set Dm 90 252325 252325 254321 255320
Clamp insert set Dm 110 252326 252326 254322 255321
Clamp insert set Dm 125 252327 252327 254323 255322
Clamp insert set Dm 140 252328 252328 254324 255323
Clamp insert set Dm 160 254325 255324
Clamp insert set Dm 180 254326 255325
Clamp insert set Dm 200 254327 255326
Clamp insert set Dm 225 254328 255327
Clamp insert set Dm 250 255328
Clamp insert set Dm 280 255329
Pipe support right/left 252350 252350 254350 255350
Pipe support insert set Dm 40 252370 252370
Pipe support insert set Dm 50 252371 252371
Pipe support insert set Dm 56 252372 252372
Pipe support insert set Dm 63 252373 252373
Pipe support insert set Dm 75 252374 252374 254370
Pipe support insert set Dm 90 252375 252375 254371 254371
Pipe support insert set Dm 110 252376 252376 254372 254372
Pipe support insert set Dm 125 252377 252377 254373 254373
Pipe support insert set Dm 140 252378 252378 254374 254374
Pipe support insert set Dm 160 254375 254375
Pipe support insert set Dm 180 254376 254376
Pipe support insert set Dm 200 254377 254377
Pipe support insert set Dm 225 254378 254378
Pipe support insert set Dm 250 254378 254379
Pipe support insert set Dm 280 255379
Pipe cutter REMS RAS P 10 - 40 290050 Pipe shear REMS ROS P 35 291200
Pipe cutter REMS RAS P 10 - 63 290000 Pipe shear REMS ROS P 35 A 291220
Pipe cutter REMS RAS P 50 -110 290100 Pipe shear REMS ROS P 40 291000
Pipe cutter REMS RAS P 110 -160 290200 Pipe shear REMS ROS P 42 291250
Pipe chamfering tool REMS RAG P 16 -110 292110 Pipe shear REMS ROS P 75 291100
Pipe chamfering tool REMS RAG P 32 -250 292210 Pipe support REMS Herkules 120100
1.2. Capacity
Pipe diameter 40-160 mm 40-160 mm 75-250 mm 90-315 mm
All weldable plastics for sanitary installation, drain pipes, chimney reconstruction,with welding temperatures 180-290°C.
1.3. Electric data
Rated voltage (mains,voltage) 230 V 230 V 230 V 230 V
Rated power input 1700 W 1700 W 1800 W 2800 W
Butt welding unit 1200 W 1200 W 1300 W 2300 W
Electric facing cutter 500 W 500 W 500 W 500 W
Rated frequency 50 Hz 50 Hz 50 Hz 50 Hz
Protection class all units protection class 1 (earth conductor)
1.4. Dimensions
Transport L 660 mm 800 mm 800 mm 1230 mm
W 380 mm 520 mm 520 mm 680 mm
H 535 mm 760 mm 760 mm 1030 mm
Operation L 1100 mm 1030 mm 1350 mm 1230 mm
W 500 mm 800 mm 800 mm 1220 mm
H 900 mm 1320 mm 1450 mm 1500 mm
1.5. Weight
Machine 35 kg 80 kg 100 kg 158 kg
Clamp, Support inserts 13,5 kg 12,5 kg 15 kg 64 kg
1.6. Noise information
Emission at workplace 85 db (A) 85 db (A) 85 db (A) 85 db (A)
1.7. Vibrations
Weighted effective value of acceleration 2,5 m/s 2 2,5 m/s 2 2,5 m/s 2 2,5 m/s 2
2. Preparations for use
2.1. Transporting and setting up the machine
REMS SSM 160 R
The machine is delivered and transported or set up as shown in Fig. 2. The
clamping and pipe support inserts and operating key are transported or kept in
a separate steel case (1). To set up the machine, withdraw the four split pins
(2) from the ends of the tubes, lift the tubular stand (3) off the machine and
place it inverted on the floor, so that the ends of the tubes are pointing upwards.
The machine is now mounted on the tubular stand. The ends of the four tubular
legs project above the four eyes in the machine chassis to a sufficient extent to
allow the four split pins (4) to be reinstalled. Install the jointing lever (7). For trans-
porting purposes, proceed in the reverse order. The machine can be secured
to a workbench if required.
REMS SSM 160 K and REMS SSM 250 K
The machine is delivered and transported or set up as shown in Fig. 3. The
clamping and pipe support inserts and operating key are transported or stored
in a separate drawer (8) in the steel base. To set up the machine, release the
four catches (9) at the bottom of the transport case. Lift up the case and place
it on the floor so that the four catches are next to the floor. Now place the ma-
chine on the carrying case. Caution! Take care to ensure that the drawer (8)
does not fall out. The machine is centred in the rectangular recess in the top of
the case. For transporting purposes, proceed in the reverse order. The machine
can be secured to a workbench if required.
A plastic cover is available to protect the heating element in transit. This must
be removed without fail before the heating element is switched on or, for trans-
porting purposes, only after the heating element has cooled, otherwise the
cover will be destroyed and the machine damaged.
REMS SSM 315 RF
The machine is delivered and transported or set up as shown in Fig.4. The
clamping and pipe support inserts and operating key are transported and kept
in a separate box (1) .To set up the machine, release the tow bar (10) from the
bayonet catch (11) and remove. Rotate the machine about the transverse axis
(tubular stand axis) so that the wheel assembly is facing upwards. Release
locking lever (12). Caution! In doing so, hold the machine securely onto the
frame. Swivel the machine carefully about the longitudinal axis, resecure locking
lever (12). For transporting purposes, proceed in the reverse order. The ma-
chine can be used on the transit chassis if the tubular stand is removed by re-
moving the two opposing allen screws (3) and releasing the locking lever (12).
To mount the machine on a workbench, the support (14) and wheeled frame
(15) must be removed in addition to the tubular stand.