Reliance electric DC2 VS series страница 47 Скачать руководство пользователя

Страница: 47 / 56

Table 52. Servicing Steps. (Continued)

Motor does not
reach top speed

or deliver rated
torque.

Low line voltage.

Check for rated line voltage
and correct if not within 10%

of the input voltage rating.

Unstable
speed or poor

regulation when
applied as an

armature voltage
regulator.

Incorrectly set IR drop com
pensation pot.

Readjust IR drop compensa
tion pot. Check tachometer.

Incorrect speed
with tachometer

feedback.

Motor runs at
maximum

uncontrolled
speed with

tachometer
feedback

DC tachometer polarity not
correct for given direction of

motor rotation, 419 negative
with respect to 519.

Verify DC tachometer polar
ity and lead connection.

Motor speed
unstable with

changing load.
(Tach Feedback

only)

IR drop compensation pot not
set at zero (CCW).

Set IR drop compensation
pot to zero (CCW).

With Process Control models,
improperly set maximum

speed pots.

Reset maximum speed pots.

With Process Control models,
reference signal producing

less than expected maximum
value.

Adjust source of automatic
reference signal or proper

output signal range.

Overload.

Check for cause of overload
and correct.

Improper position jumper.

Check and reconnect
jumper(s) as necessary:

J200: Tach Scaling Jumper

J3: Controller Output

Current Jumper

Faulty circuit board.

Replace entire controller.

Faulty circuit board.

Replace entire controller.

No DC tachometer output
signal.

Verify tachometer voltage.
Verify tachometer coupling.

Indication

Possible Cause

Corrective Action

Improper feedback selection
at J3.

Check J3 for proper feedback
selection and reposition as

required.

Open field for voltage
Regulators only.

Measure motor field resistance
from drive and connect the

voltage field as required.

Содержание DC2 VS series

























































Результаты поиска

Содержание DC2 VS series

Отзывы:

Похожие инструкции для DC2 VS series

Бренды по названию

Популярные бренды

Reliance electric DC2 VS series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание DC2 VS series

Отзывы:

Похожие инструкции для DC2 VS series

Бренды по названию

Популярные бренды