Reliance electric DC2 VS series страница 23 Скачать руководство пользователя

Страница: 23 / 56

Wire the Drive

DANGER

THE USER IS RESPONSIBLE FOR CONFORMING TO THE NATIONAL ELEC

TRICAL CODE AND ALL OTHER APPLICABLE LOCAL CODES. WIRING

PRACTICES, GROUNDING, DISCONNECTS AND OVERCURRENT PROTEC

TIONS ARE OF PARTICULAR IMPORTANCE. FAILURE TO OBSERVE THESE

PRECAUTIONS COULD RESULT IN SEVERE BODILY INJURY OR LOSS OF

LIFE.

DANGER

THIS EQUIPMENT IS AT LINE VOLTAGE WHEN AC POWER IS CONNECTED.

DISCONNECT AND LOCKOUT ALL UNGROUNDED CONDUCTORS OF THE A

C POWER LINE. FAILURE TO OBSERVE THESE PRECAUTIONS COULD RE

SULT IN SEVERE BODILY INJURY OR LOSS OF LIFE.

NOTE:

All remote operation wiring should be no longer than 250 feet.

Ground the Controller and Enclosure, the Motor
and the Operator's Control Station.

DANGER

CONNECT THE GROUND WIRE BROUGHT IN WITH THE INCOMING AC

POWER LINE TO THE CONTROLLER GROUND POINT. CONNECT AN APPRO

PRIATE EQUIPMENT GROUNDING CONDUCTOR UNBROKEN FROM THE

CONTROLLER GROUND POINT, THE MOTOR FRAME, THE TRANSFORMER

ENCLOSURE IF USED, THE CONTROLLER ELECTRICAL ENCLOSURE, THE

WIRING CONDUITS, AND THE OPERATOR'S CONTROL STATION TO AN AP

PROPRIATE GROUNDING ELECTRODE. FAILURE TO OBSERVE THIS PRE

CAUTION COULD RESULT IN SEVERE BODILY INJURY OR LOSS OF LIFE.

1. Locate the convienence ground point provided at the bottom edge

of the heat sink.

2. Run a suitable equipment grounding conductor

unbroken

from this

controller ground point to the plant ground (grounding electrode). A

ring lug is recommended at the ground point.

3. Connect a suitable grounding conductor from each conduit to this

controller ground point.

4. Connect a suitable equipment grounding conductor to the motor

frame, the transformer enclosure if used, and the controller

enclosure. Run this conductor

unbroken

to the grounding

electrode.

5. Connect the ground wire brought in with the incoming AC power

line to the controller ground point.

Содержание DC2 VS series

























































Результаты поиска

Содержание DC2 VS series

Отзывы:

Похожие инструкции для DC2 VS series

Бренды по названию

Популярные бренды

Reliance electric DC2 VS series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание DC2 VS series

Отзывы:

Похожие инструкции для DC2 VS series

Бренды по названию

Популярные бренды