Reliance electric DC2 VS series страница 12 Скачать руководство пользователя

Страница: 12 / 56

Process Interface (PI) bias adjustment

Ramp generator

Auxiliary form C contact for run indication

Jog Functions
(Models DC240, 50, 60, 78, 79, 80, 98, 99)

All features listed in Basic Controller Features (All Models)"

Controller offers Run/Jog capability for local or remote

requirements.

Available in chassis and enclosed controller designs.

Controller Specifications

Ratings

Service factor 1.0

Continuous duty

Load capacity: 150% for 1 minute

Line voltage variations: +10% of rated

AC line frequency: 48 to 62 Hertz

Maximum allowable symmetrical AC line fault current: 10,000

amperes

Maximum AC line distribution system KVA capacity

(1) (2)

Maximum KVA:

115volt AC input: 65.0 KVA

230volt AC input: 32.5 KVA

Controller ratings by motor horsepower: Refer to Table 24

Ambient temperature:

- Open chassis plate style models:

to 55

C (32

to 131

- NEMA/UL 12 enclosed:

to 40

C (32

to 104

- NEMA/UL 4/4X/12 enclosed:

to 40

C (32

to 104

Altitude: 3300 feet (1000 meters) maximum

NonCondensing Relative Humidity 5 to 95%

NEMA 12 enclosure is intended for indoor use. It provides protection

against fibers, metal filings, lint, dust, dirt and light splashing,

seepage, dripping and external condensation of noncorrosive

liquids. It will not protect against internal condensation.

NEMA 4/4X/12 enclosure is intended for use indoors to protect the

enclosed equipment against splashing water, seepage of water,

falling or hosedirected water, and severe external condensation.

Conduit hubs for watertight connection are provided at the conduit

entrance and a means to mount these hubs external of the

equipment cavity. The Reliance DC2 controller has passed the UL

hosedown test to verify the washdown integrity of the controller.

(1)

When applying DC2 drives to power distribution systems with a KVA capacity in excess

of the maximum recommended KVA capacity, an isolation transformer or line reactor of

similar impedance is required.

(2)

Assumes a transformer impedance of 5%.

Содержание DC2 VS series

























































Результаты поиска

Содержание DC2 VS series

Отзывы:

Похожие инструкции для DC2 VS series

Бренды по названию

Популярные бренды

Reliance electric DC2 VS series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание DC2 VS series

Отзывы:

Похожие инструкции для DC2 VS series

Бренды по названию

Популярные бренды