Regency Liberty LRI4E series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 72

background image

LRI4E / HRI4E-11 Direct Vent Gas Insert

| 33

installation

HRI4E OPTIONAL LOG SET INSTALLATION

919-350b

07.18.16

Ensure unit is cooled to room temperature and remove glass door.

1. HRI4E Unit only.

Remove burner (see manual for instructions).
Remove existing pilot shield by removing 2 screws.
Install pilot shield provided with Log Set using 2 screws from

previous pilot shield. Reinstall burner.

Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced. Broken
logs can interfere with pilot operation.

Improper positioning of the logs and glass crystals may create carbon build-up and can alter the unit's performance which is not cov-
ered under warranty.

*For Touch Ups:

Dark Brown paint is included.

Note:

This Log installation is for

NG

units only.

1

Rear Centre Log

2

Centre Right Front Angled Log Piece

3

Right Forked Upright Log

4

Left Angled Upright Log

5

Left Angled Cross Log

6

Right Front Angled Log Piece

7

Centre Left Front Angled Log Piece

Rear Log Bracket (HRI6E/HRI4E units)

Pilot shield (HRI4E units

only)

Lava Rock and Embers

1

2

3

4

7

6

5

Glass/Beads quantities with Log installation

HRI4E

6 lbs

HRI6E

9 lbs

Note

: If glass previously installed - remove 2lbs to equal above quantity.

2.

Both HRI4E & HRI6E Units:

Sweep glass aside from pilot covers (if already installed) to install

Rear Log Bracket. Rest the front edge of the Rear Log Bracket on the
back of the burner screen cover and clip the front edge of the rear
bracket on to rear of the burner as shown in Diagram 2.

IMPORTANT:

After the Rear Log Brackets are installed glass crystals

must be reapplied. Glass crystals should not be higher then the bottom
of the pilot screen cover as shown in Diagram 3. Pilot area needs to be
clear to allow proper ignition as shown in Diagram 3.

Rear Log Brackets

New Pilot Shield - HRI4E Only

Reapply glass crystals on burner as shown below.

Do not apply any glass crystals over the pilot/burner

screen cover. This must remain free and clear and

is required for air fl ow.

Pilot Area

Rear Log Brackets

Pilot Area

NOTE:

HRI4E shown above. The HRI6 pilot (not shown) is located on

the left hand side.

Pilot/Burner Screen Cover

Pilot/burner screen cover

Diagram 3

Diagram 2

Diagram 1

1

HRI6E / HRI4E

OPTIONAL LOG SET INSTALLATION

«
...
31
32
33
34
35
...
»

Содержание Liberty LRI4E series









































































Отзывы:

Нет отзывов

Похожие инструкции для Liberty LRI4E series

Бренд: Sunnydaze Decor Страницы: 2

Бренд: Calflame Страницы: 32

Бренд: Napoleon Страницы: 40

Montgomery BIO-20-218

Бренд: CACHFIRES Страницы: 17

Бренд: Dik Geurts Страницы: 92

Бренд: Dimplex Страницы: 2

Бренд: Heat & Glo Страницы: 2

Бренд: QualityCraft Страницы: 12

Бренд: Costway Страницы: 10

Бренд: Napoleon Страницы: 132

Бренд: Superior Страницы: 28

Harman Accentra Insert

Бренд: Harman Home Heating Страницы: 48

Бренд: Uberhaus Страницы: 7

Superior Fireplaces Elite VRE4336ZEN

Бренд: IHP Страницы: 16

Бренд: baltur Страницы: 72

Squaw Valley L-FT629PST

Бренд: Sunjoy Страницы: 4

L-FT253PST-6A-1

Бренд: Sunjoy Страницы: 6

Бренд: Sunjoy Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды