Regency Liberty LRI4E series Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 72

background image

LRI4E / HRI4E-11 Direct Vent Gas Insert

| 39

installation

BRICK PANEL INSTALLATION

IMPORTANT: THIS APPLIANCE CANNOT BE OPERATED WITHOUT BRICK OR ENAMEL PANELS INSTALLED.

919-024b

11.20.17

1

BRICK PANEL INSTALLATION

Brick panels are soft and fragile. Use caution when handling the panels,

being careful not to jar them or scratch the painted surfaces.

1. Remove left/right filler sections and discard - see below.

5. Once one Firebox Liner Side is installed, you can release the Firebox Liner

Rear. The side Liner will hold the rear Liner in place. Install the Firebox
Liner Left the same way you installed the Firebox Liner Right. Both side
liners should be just slightly back from the front edge of the Firebox.

Firebox Liner Left

Firebox Liner Right

Firebox Liner Rear

Firebox Liner Retainers

Firebox Liners

Upper Left of Firebox

Exhaust Baffle

Firebox Liner Left

Lower Right of Firebox

Firebox Liner

Retainer (x2)

Firebox Liner Right

Left /right filler sections

2. Remove the firebox liners from their packaging. Inspect them prior to

installation to make sure they haven`t been damaged during shipping.

3. Install the rear brick panel, by placing it against the rear of the firebox.

The bottom of the brick panel rests on a small sheet metal lip, just above
the air intake at the bottom rear of the Firebox. You will need to hold this
panel in place while you install the right brick panel. Do not let go of the
panel or it may fall forward and be damaged.

4. While holding the rear brick panel in place, slide the right along the side

of the firebox toward the rear of the firebox. Each side Firebox Liner will
sit upon a Firebox Liner Retainer and the top will be held between the
Exhaust Baffle and the side of the firebox.

Diagram 1

Diagram 2

Diagram 3

Diagram 4

Diagram 5

6. If the brick panels are difficult to get into place the firebox liner retainer

can be adjusted to accommodate the brick panel, The burner will need to
be removed by removing 2 screws as shown in Diagram 4. Lift burner up
and out towards you and put on a soft cloth. Loosen the 2 screws securing
the Firebox liner retainers (Diagram 5) and adjust inward. Check to ensure
brick panel will fit prior to tightening. Repeat for other side. Reinstall burner
prior to reinstalling brick panels

Brick Panel Installation

LRI4E

«
...
37
38
39
40
41
...
»

Содержание Liberty LRI4E series









































































Отзывы:

Нет отзывов

Похожие инструкции для Liberty LRI4E series

Бренд: Napoleon Страницы: 4

Бренд: LA NORDICA Страницы: 80

Бренд: Valor Страницы: 6

Бренд: DS Produkte Страницы: 2

Бренд: Bluegrass Living Страницы: 30

Бренд: Majestic Страницы: 8

MANDALAY Series

Бренд: Warnock Hersey Страницы: 38

Бренд: California Outdoor Concepts Страницы: 8

Бренд: CC Products Страницы: 7

Kingsman Marquis MCVP42N

Бренд: R-Co Страницы: 65

Бренд: CSA Страницы: 22

Бренд: BCP Страницы: 16

Бренд: Rocal Страницы: 33

Black Beauty Radiant 340

Бренд: Valor Страницы: 9

Бренд: Valor Страницы: 60

Бренд: Landmann Страницы: 6

Deck Open Chimeneas

Бренд: Arada Страницы: 8

FALLSTON 1006152671

Бренд: Home Decorators Collection Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды