Regency Liberty LRI4E series Скачать руководство пользователя страница 64

Страница: 64 / 72

64 |

LRI4E / HRI4E-11 Direct Vent Gas Insert

parts list

ARCHED VIGNETTE FACEPLATE

Part #

Description

Front Plate Arched Vignette

399-164

Mounting Bracket (left)

399-165

Mounting Bracket (right)

Midplate

Edge Frame - No Knockout

Edge Frame w/o Knockout (right)

Top Edge Trim

Top Scratch Guard

399-847

Backing Plate

399-845

Decorative Arched Front Assembly

Screen and Panels Assembly

399-840

Spacer Assembly

CHK
PROCESS :

SCALE:

DWN

BLANK SIZE :

SIGN

C.N.

DATE

THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.

CURRENT REVISION

PREVIOUS REVISION

PART :

MAT'L :

ANGULAR =

INSIDE BEND RADII =

UNITS IN INCHES

DIMENSIONS =

TOLERANCES UNLESS

OTHERWISE STATED

SCALE

DO NOT

PROJECTION

3RD ANGLE

MODEL #

QTY.

REV.

±1°

±0.031

PART

NO.

FIREPLACE PRODUCTS INTERNATIONAL

09/25/2018

SEE ABOVE

399-550

anunn

399-550

LRI4E ARCHED FRONT ASSEMBLY
-

1:16

ITEM NO. PART NUMBER

DESCRIPTION

QTY.

399-163

LRI4E FRONT PLATE

399-164

LRI4E MOUNTING

BRACKET (LEFT)

399-165

LRI4E MOUNTING

BRACKET (RIGHT)

399-166

LRI4E MIDPLATE

399-167

LRI4E EDGE FRAME

NO KNOCKOUT

(LEFT)

399-168

LRI4E EDGE FRAME

WITH KNOCKOUT

(RIGHT)

399-169

LRI4E TOP EDGE

TRIM

299-183

LRI6E TOP SCRATCH

GUARD

399-182

LRI4E BACKING

PLATE

399-551

LRI4E DECORATIVE

ARCHED FRONT

ASSEMBLY

399-552

LRI4E SCREEN AND

PANELS ASSEMBLY

399-553

LRI4E SPACER

ASSEMBLY

399-554

LRI4E ARCHED

VIGNETTE ASSEMBLY

904-791

CUP MAGNET 1/2" x

5/8" OD

904-790

MAGNET ROUND

1/2" x 1/8"

948-020

CLIP SPRING

Part #

Description

399-843

Arched Vignette Assembly

904-791

Cup Magnet 1/2" x 5/8" OD (Each)

904-790

Magnet Round 1/2" x 1/8" (Each)

948-020

Clip Spring (Each)

Содержание Liberty LRI4E series









































































Результаты поиска

Содержание Liberty LRI4E series

Отзывы:

Похожие инструкции для Liberty LRI4E series

Бренды по названию

Популярные бренды

Regency Liberty LRI4E series, Инструкция для владельца и по установке

Результаты поиска

Содержание Liberty LRI4E series

Отзывы:

Похожие инструкции для Liberty LRI4E series

Бренды по названию

Популярные бренды