Regency Liberty LRI4E series Скачать руководство пользователя страница 51

Страница: 51 / 72

LRI4E / HRI4E-11 Direct Vent Gas Insert

| 51

operating instructions

919-560

04/30/15

LRI4E/HRI4E/LRI6E/HRI6E/E33

OPTIONAL HEARTH TRIM

INSTALLATION -

VIGNETTE FACEPLATE WITHOUT SPACER

Customizing the Hearth Trim

The Hearth Trim can be adjusted to custom fit an installation by
pulling apart the top piece from the bottom piece. Minimum height
of the hearth trim is 2” and can be adjusted up to maximum 6”.

1. Discard the spacer brackets, as these are not required when installing

the unit without spacer.

2. Cut the top of the bottom piece of the hearth trim to the appropriate

height using a metal cutting blade.

NOTE: The tab bends at the back of the top piece of the hearth trim

should be used as the measuring point to the hearth to measure
the height required.

4. Line up the hearth trim with base of the unit and secure it with 3 screws

as shown below.

3. Reattach the top piece of the hearth trim to the cut bottom piece by

fitting in place.

(152 mm)

(51 mm)

Содержание Liberty LRI4E series









































































Результаты поиска

Содержание Liberty LRI4E series

Отзывы:

Похожие инструкции для Liberty LRI4E series

Бренды по названию

Популярные бренды

Regency Liberty LRI4E series, Инструкция для владельца и по установке

Результаты поиска

Содержание Liberty LRI4E series

Отзывы:

Похожие инструкции для Liberty LRI4E series

Бренды по названию

Популярные бренды