Regency Liberty LRI4E series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 72

background image

LRI4E / HRI4E-11 Direct Vent Gas Insert

| 31

installation

MEDIA INSTALLATION

Installing Glass Crystals

Spread the Media evenly over the burner. Ensure installed media does not overlap excessively as this will affect the flame pattern.

IMPORTANT NOTE:
Only the supplied approved Media is to be used with these fireplaces. Use of any other type of media can alter the unit's performance, any damage caused
by the use of any unapproved media will not be covered under warranty.
When using Ceramic Spa/Volcanic Stones

DO NOT cover burner ports or pilot light that leads to pilot flame.

BURNER PACKAGES

Unit

Glass Crystals Fire Beads

Stones - Spa / Ceramic / Volcanic Stones / Pebbles / Driftwood Logs

HRI4E

8 lbs [5 lbs
3 lbs firebox]

8 lbs [5 lbs
3 lbs firebox]

7 lbs Glass (burner) + 1 package (70 Spa Stones)
8 lbs Beads (burner) + 1 package (70 Spa Stones)
4 lbs Glass (burner) + 26 Volcanic Stones
8 lbs Beads (burner) + 26 Volcanic Stones
5 lbs Glass (burner) + 3 bags Pebbles (around firebox base)

NOTE: Media is not supplied with the unit. Must purchase separately - see quantities above.
Spa stone package contains 70 stones.

DO NOT block pilot area with glass crystals

Glass Crystals shown on Burner and Firebox Floor

«
...
29
30
31
32
33
...
»

Содержание Liberty LRI4E series









































































Отзывы:

Нет отзывов

Похожие инструкции для Liberty LRI4E series

Бренд: Four Seasons Courtyard Страницы: 12

Бренд: Martin Страницы: 36

Бренд: Napoleon Страницы: 20

Бренд: Solas Страницы: 6

Бренд: Bali Страницы: 16

Бренд: Mainstays Страницы: 37

Бренд: Greentouch Страницы: 42

Бренд: Fire Sense Страницы: 5

Бренд: hergom Страницы: 93

Бренд: Riello Страницы: 44

Бренд: Jøtul Страницы: 120

Бренд: Majestic Страницы: 29

Бренд: Vanguard Страницы: 40

Бренд: Dimplex Страницы: 20

Бренд: barbas Страницы: 40

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 4

Бренд: Glen Dimplex Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды