Regency Liberty LRI4E series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 72

background image

56 |

LRI4E / HRI4E-11 Direct Vent Gas Insert

maintenance

GLASS CRYSTAL BURNER REMOVAL / INSTALLATION - HRI4E

Care must be taken when installing the burner into the firebox.

Do not damage, knock or scrap the pilot assembly.

The flame sensor and ignition lead are fragile and can be damaged

easily.

1) If already installed, remove glass crystals and ceramic spa stones.

2) Remove filler sections from right and left sides of burner. Discard filler sec-

tion if enamel panels are to be installed - see below.

1) Lift the burner assembly with both hands. Point the mixing tube towards

the rear of the firebox. Lean the rear of the burner assembly downward.
Partially lift the burner assembly so that the mixing tube will then slide
into the air shutter.

2) Lower the front edge of the burner assembly so that the burner front

mounting tab rests on the burner mounting bracket left and right, near
the front of the firebox. These tabs will not line up unless the mixing tube
is inside the air shutter at the rear of the firebox.

Glass / Media Burner

* Side view cut-through *

Burner

Pilot Cover

Burner Screen

Glass / Media

Tray

Fill Glass / Media

to this level

Mixing Tube

Disconnect unit from gas supply and allow unit to cool before removing

burner.

Filler section

GLASS BURNER REMOVAL

GLASS BURNER INSTALL

3) Place the Burner Cover Screen over the Burner Ports. Place the Pilot

Cover over the rear gap between the Burner and the Media Tray. This will
sit around the Pilot Provision.

4) Distribute the glass crystals throughout the Media Tray. The media should

be level with the side of the Media Tray.

*

* Do not to install glass or other media over or in front of the Pilot

Provision as shown.

Burner

Burner Screen

Mixing Tube

Air Shutter

Burner Mounting Brackets

Important:
Do not to install glass or
other media in this area, as
this will block the path of the
pilot to the burner.

3) Remove the 2 screws as shown. Lift the burner with both hands.

4) Pull gently upwards and outwards to the front of the firebox.

5) Continue onto burner installation.

«
...
54
55
56
57
58
...
»

Содержание Liberty LRI4E series









































































Отзывы:

Нет отзывов

Похожие инструкции для Liberty LRI4E series

Бренд: Napoleon Страницы: 4

Бренд: Quadra-Fire Страницы: 40

Бренд: homechoice Страницы: 8

Бренд: Whalen Страницы: 52

ISOKERN Standard 36

Бренд: EarthCore Страницы: 12

E-SLIM LINEAR 1200/450 I

Бренд: Faber Страницы: 31

Бренд: Outdoor GreatRoom Company Страницы: 12

Бренд: Lopi Страницы: 3

New York Corner

Бренд: Nordpeis Страницы: 20

Бренд: Majestic Страницы: 60

Бренд: Chinook Fireplaces Страницы: 16

Бренд: IHP Страницы: 4

Бренд: Northern Tool Страницы: 7

Бренд: Verine Страницы: 28

Бренд: Megamaster Страницы: 4

Бренд: GlammFire Страницы: 12

Бренд: GlammFire Страницы: 16

Apollo III Crea7ion.M

Бренд: GlammFire Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды