Regency Liberty LRI4E series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 72

background image

LRI4E / HRI4E-11 Direct Vent Gas Insert

| 45

installation

SPACER INSTALLATION

919-662

05.18.16

1

4E/6E

tooltip

1. Remove Vignette faceplate from unit and lay on a soft surface.

SPACER INSTALLATION

4. Place the spacer on a soft cloth on the floor. Lay the outer faceplate

over the spacer and line up the 7 holes. Attach the 3 piece spacer to
the back of the outer faceplate from the front with 7 screws (3 along
the top and 2 on each side).

3. Separate the Outer Faceplate from the Backing Plate by removing

7 screws.

5. Reinstall the outer faceplate and spacer—reverse Step 2.

6. Reinstall the Vignette faceplate and safety screen to complete.

2. Remove the outer faceplate by removing the 5 screws as shown.

Note: the two top and two bottom screws can be loosened - slide the

outer faceplate up on out to remove.

«
...
43
44
45
46
47
...
»

Содержание Liberty LRI4E series









































































Отзывы:

Нет отзывов

Похожие инструкции для Liberty LRI4E series

Бренд: Valcourt Страницы: 100

Бренд: Valcourt Страницы: 53

FP-7-LM ANTOINETTE

Бренд: Valcourt Страницы: 56

Бренд: Valcourt Страницы: 62

Бренд: Paloform Страницы: 17

DVCP(32,36,42)BP30(N,P)-3DVCP(32,36,42)BP30(N,P)-3DVCP(32,36,42)BP30(N,P)-3DVCP(32,36,42)BP30(N,P)-3DVCP(32,36,42)BP30(N

Бренд: Empire Страницы: 56

Бренд: HAMPTON BAY Страницы: 40

Бренд: KENT Страницы: 2

Бренд: Travis Industries Страницы: 2

(V)KC42NE SERIE

Бренд: Desa Страницы: 40

Бренд: Valor Страницы: 6

Inglenook IWZC-02

Бренд: Country Flame Страницы: 54

MODEL OSBURN STRATFORD

Бренд: Stove Builder International Страницы: 38

LHEACNSS Contour KT1B80

Бренд: Vermont Castings Страницы: 2

Бренд: Dru Страницы: 24

Бренд: Amantii Страницы: 20

Бренд: Valor Страницы: 16

Бренд: Comfort Glow Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды