Regency Liberty LRI4E series Скачать руководство пользователя страница 49

Страница: 49 / 72

LRI4E / HRI4E-11 Direct Vent Gas Insert

| 49

installation

OPTIONAL MANTEL DEFLECTOR INSTALLATION - VIGNETTE

919-664

07.13.16

4E/6E

tooltip

Backing Plate

Outer Faceplate

Mantel Deﬂector

tooltip

NOTE: A mantel deflector may be installed to reduce the minimum

mantel height. Refer to the instruction manual for minimum
mantel clearances.

1. Remove Vignette faceplate from unit and lay on a soft surface.

MANTEL DEFLECTOR INSTALLATION

4. Install the mantel deflector in between the back of the outer face-

plate and the front of the backing plate. Insert the screws from the
front of the outer faceplate using 3 screws.

5. Reinstall the outer faceplate and spacer—reverse Step 2.

6. Reinstall the Vignette faceplate and safety screen to complete.

2. Remove the outer faceplate by removing the 5 screws as shown.

Note: the two top and two bottom screws can be loosened - slide the

outer faceplate up on out to remove.

3. Separate the Outer Faceplate from the Backing Plate by removing

7 screws.

Содержание Liberty LRI4E series









































































Результаты поиска

Содержание Liberty LRI4E series

Отзывы:

Похожие инструкции для Liberty LRI4E series

Бренды по названию

Популярные бренды

Regency Liberty LRI4E series, Инструкция для владельца и по установке

Результаты поиска

Содержание Liberty LRI4E series

Отзывы:

Похожие инструкции для Liberty LRI4E series

Бренды по названию

Популярные бренды