Raymarine STV60 Скачать руководство пользователя страница 5

Страница: 5 / 82

Please carefully read and follow the installation, operating and

maintenance procedures, to ensure optimum performance.

Geographic location

Your STV system will operate in various geographic regions,

dependant upon the type of satellite signal available.
Broadly speaking different regions around the globe use either

circular or linear polarization for DVB satellite broadcasts. Each

signals.
Some examples of regions using circular and linear polarization

are below.

Circular polarization:

• North America

Linear polarization:

• Europe
• Australia
• New Zealand
• China
• Middle East

For further assistance please refer to your regional satellite service

providers or Raymarine technical support.

Changing location

If you change your area of operation, you may need to arrange for

•

Adjust the antenna low noise block (LNB) as appropriate for the

area in which you are operating.

• Update the region information using your control unit (ACU) or a

PC running the GUI software.

• Ensure that your satellite receivers (IRDs) will operate and receive

DVB broadcasts at your new location.

Important: Please refer all servicing / component replacement to

authorized Raymarine agents.

Satellite coverage

Up to date coverage maps and satellite information may be found

on the appropriate website of your satellite service provider.

Television reception

For full functionality of your STV System, you must subscribe to the

relevant service(s) from the appropriate service provider(s). Full

details of service providers are given.

EMC installation guidelines

Raymarine equipment and accessories conform to the appropriate

Electromagnetic Compatibility (EMC) regulations, to minimize

electromagnetic interference between equipment and minimize the

effect such interference could have on the performance of your

system
Correct installation is required to ensure that EMC performance is

not compromised.

For

optimum EMC performance we recommend that wherever

possible:
• Raymarine equipment and cables connected to it are:

– At least 1 m (3 ft) from any equipment transmitting or cables

carrying radio signals e.g. VHF radios, cables and antennas.

STV unit is configured to receive either Linear or Circular polarized

modification to your STV system.

Содержание STV60



















































































Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды

Raymarine STV60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды