Raymarine STV60 Скачать руководство пользователя страница 51

Страница: 51 / 82

Setting Antenna Go Position

The antenna can be controlled manually by using the ACU.

1. Press YES to enter setup mode.

2. Press NEXT 10 times to enter Antenna

Go Position mode.

3. Press YES to go position.

4. Input position value for azimuth (AZ) axis.

+increases the value. - decreases the value.

Change the underscored digit using the

+/- buttons.

Press INPUT to accept the value and move

to next digit.

Press BACK to move to previous digit.

Press ENTER to move to next screen.

SETUP MODE ?

SET SAT PAIR ?

ANT GO POSITION ?

GO TO AZ : ##.#

YES

INPUT

X10

5. Input position value for elevation (EL) axis.

+ increases the value. - decreases the

value.

Change the underscored digit using the

+/- buttons.

Press INPUT to accept the value and move

to next digit.

Press BACK to move to previous digit.

Press ENTER to move to next screen.

6. Press YES to move the antenna to input

position.

Press NO to return to the Antenna Go

Position mode.

7. Press EXIT to return to main setup mode.

GO TO EL : ##.#

AZ:###.# EL:###.#

YES

EXIT

INPUT

GO TO POSITION ?

Содержание STV60



















































































Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды

Raymarine STV60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды