Raymarine STV60 Скачать руководство пользователя страница 59

Страница: 59 / 82

Auto Update

Aptus

checks and notifies the latest version when it is

started to maintain up to date software version.

1. When Aptus

is started, it automatically checks the latest

software version from the server and runs AutoUpdate if new

version is available.

2. Current software version information is displayed.

3. It notifies new software version information.

4. When you click the “start” button, “File downloading…”

message is displayed while downloading files from the server.

5. When file downloading is finished, “installing…” message

is displayed and the Aptus patch runs and the installation

starts by InstallShield.

6. Click the “Finish” button when InstallShield installation

is finished. The “Run the Aptus” message is then displayed

and Aptus runs and AutoUpdate is automatically finished.

Содержание STV60



















































































Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды

Raymarine STV60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды