Raymarine STV60 Скачать руководство пользователя страница 14

Страница: 14 / 82

Raymarine Satellite TV Antenna Systems

Planning the Installation

Selection of Antenna Installation Site

The antenna should be installed in a place where there is all

round clear view of the horizon. Please be sure there are no

obstacles within 15° above the antenna. Any obstacles can

prevent the antenna from tracking the satellite signal (Refer

to the drawing on the right).

Do not install the antenna near the radar especially on the

same plane. Its energy levels may overload the antenna

front-end circuits. It is recommended to position the antenna

at least 4 feet (1.2m) above or below the level of the radar

and minimum of 15 feet (4.6m) away from the high power

short wave radars.

The mounting platform should be rigid and not subjected

to excessive vibration. The movement of the antenna can

be minimized by installing at the center of the vessel. For

optimal performance of the antenna, it is not recommended

to install at any corner of the vessel, where the movement of

the vessel is the greatest. Install the bottom of the antenna

parallel to the surface of the sea and fix tightly to the

structure of the vessel.

When setting the antenna down, be careful not to damage

the RF connector. Striking the connectors on the bottom

directly will damage the connector.

Figure 07 : Elevation Limit of Obstacles

15°

Antenna Unit

Obstacle

Содержание STV60



















































































Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды

Raymarine STV60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды