Raymarine STV60 Скачать руководство пользователя страница 16

Страница: 16 / 82

Raymarine Satellite TV Antenna Systems

Installation and Mounting of Antenna

The method of installing and mounting the antenna may

vary due to vessel design, but the following procedures are

applicable in most situations, and will result in a secure and

effective installation.

Confirmation of Size Prior to Installation

• Confirm the height and diameter of the bottom surface of

the antenna before installing.

• The space must be sufficient for installing the antenna unit

considering the height and diameter of the antenna.

• The height and the diameter of the bottom surface of the

antenna are as shown in the following drawing. If possible,

install the antenna using a “power tower”.

Note:

Before installing the antenna open the radome and

remove the shipping constraints from the antenna interior.

Reinstall the radome before operating the system. The

system will not perform properly if the radome is open.

Figure 08: Radome Dimension of STV60

Ø70 cm (27.5”)

72 cm (28.3”)

Содержание STV60



















































































Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды

Raymarine STV60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды