Raymarine STV60 Скачать руководство пользователя страница 8

Страница: 8 / 82

Raymarine Satellite TV Antenna Systems

Built-in GPS

Raymarine STV60 has an embedded GPS, which allows for

the system to upload the GPS data automatically into the

system for an even faster and more stable system.

Built-in automatic skew angle control system

The automatic skew control system allows the STV60 to

maintain the optimal skew angle at all times and ensure

maximum level of satellite signal level.

Ethernet Port for management

The Ethernet Port on the rear panel of the ACU enables

direct and simple network connection between a PC and

the ACU. By connecting to an ISP or the modem linked with

VSAT systems, STV60 can be monitored, controlled, and

diagnosed remotely from anywhere, anytime through the

TCP/IP protocol.

This can not only save tremendous time but also saves the

cost generated from the hundreds of routine maintenance

activities such as operating firmware upgrades, tracking

parameters resets, and system diagnostics.

Wireless Connectivity and Aptus mobile

The built-in WiFi enables the ACU to be wirelessly

connected. Any kind of wireless devices such as PCs,

laptops and smartphones can be used to connect to the ACU

and monitor, control and change the settings of the system

wirelessly. The Aptus mobile app is available for download

to access the ACU via Wi-Fi and operate the antenna from

iPhone, iPad or other network devices.

iPhone and iPad are registered trademarks of Apple Inc.

Содержание STV60



















































































Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды

Raymarine STV60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды