Raymarine STV60 Скачать руководство пользователя страница 66

Страница: 66 / 82

Raymarine Satellite TV Antenna Systems

Work View Tabs

Aptus® provides 7 Work View Tabs (Antenna Basic View, Antenna

Advanced View, Satellite View, Monitor View, Graph View,

Diagnostic /Network View, and GUI View) to manage the Antenna

and the Satellite configuration.

How to modify the settings on Work View;

1. Enter the Setup mode by clicking Setup icon.

2. Tick the checkbox next to the “Set” button to modify the

settings.
3. Enter the desired value then press the Set button to save the

settings.

1. Antenna – Basic Info.

This view tab provides information on the Antenna’s Current GPS

location, Skew Information, and the Antenna’s Angle. This view

tab uses the Antenna’s AZ and EL information in order to provide

a dynamic graphic user interface (UI).

GPS

: displays and sets current antenna’s GPS.

Bow Information

: not used on STV series.

Go to Position

: The current position (angle) of the antenna is

displayed.

Push the “

Go to Target Position

” button after keying in the

desired angle to move the antenna to target position.
-

Find Antenna Angle

: displays and sets the current antenna

angle. Select a desired satellite from the drop-down menu, then

longitude, azimuth, elevation and skew information are displayed.

• Find Angles & Skew Antenna GPS: finds the current

antenna angles and skew angle in relation to the longitude (orbit

position) of the antenna’s current GPS.

Содержание STV60



















































































Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды

Raymarine STV60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды