Raymarine STV60 Скачать руководство пользователя страница 72

Страница: 72 / 82

Raymarine Satellite TV Antenna Systems

Diagnostic

: select to run a full diagnostic test or single

diagnostic test.

“Green” indicator is displayed for the test under progress.

“Blue” indicates the test result as Pass while “Red” indicates

the result as Fail.

“Yellow” indicates the test has been skipped.

•

Serial Comm.

: tests the data communication

between the antenna and the ACU.
•

AZ Limit (CW)

: tests the azimuth limit (CW)

•

AZ Limit(CCW)

: tests the azimuth limit(CCW)

•

EL Limit

: tests the elevation limit.

•

LNB

: tests the LNB.

•

Sub-Reflector

: tests the Sub-Reflector.

•

Power (Ant.)

: tests the antenna power to see

whether or not it is within the nominal operating range.
•

Power (ACU)

: tests the ACU power to see whether

or not it is within the nominal operating range.
•

Receiver Connection

: tests the data communication

between the antenna and the receiver.

6. Diagnostic / Network

This view provides Antenna Diagnostic Testing and Network

Settings.

Содержание STV60



















































































Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды

Raymarine STV60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STV60

Отзывы:

Похожие инструкции для STV60

Бренды по названию

Популярные бренды