Hy-Gain AV-18HT Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 36

background image

hy-gain

308 Industrial Park Road

Starkville, MS 39759 USA

Ph:

(662) 323-9538 FAX: (662) 323655 1

I N S T R U C T I O N M A N U A L

General Description

The "Hy-Tower" is an omnidirectional, self-
supporting vertical radiator, which operates on
10 thru 80 meters. 160 meter operation is
possible with the addition of a loading coil, as
shown in Figure 13. The "Hy-Tower" is now
supplied with stainless steel hardware.

The use of stub decoupling systems allows
band switching on 10, 15, 20, 40, and 80

The stubs isolate various sections of the vertical
antenna so that an electrical 1/4-wavelength (or
odd multiple of 1/4-wavelength) exists on all
bands. On 20 meters, the 80-meter section acts
as a 3/4-wave radiator.

The tilting base of the "Hy-Tower" allows the
antenna to be completely assembled on the
ground before it is raised into position. It is
light enough for one person to assemble and for
two people to erect.

Revision 3

AV-18HT

“Hy-Tower” Vertical Antenna

10,15,20,40, and 80 Meters

Specifications

Mechanical

Total Height

53 feet (16.15m) (approximately)

Tower Construction

Galvanized steel

Wind Survival

75 mph (120.7 kmph)

Hardware

Stainless steel

Electrical

Pattern Characteristics

Omnidirectional

Gain

Unity on 20, 40, and 80 Meters

2dB on 10 and 15 Meters

Input Impedance

50 ohms

Input Power

1 kW AM; 2 kW PEP

1
2
3
...
»

Содержание AV-18HT





































Отзывы:

Нет отзывов

Похожие инструкции для AV-18HT

OBID ID ISC.ANT340/240-A

Бренд: Feig Electronic Страницы: 28

airMAX Sector AM-2G16-90

Бренд: Ubiquiti Страницы: 12

AVANT CPE 150Mbps

Бренд: Smart Lan Страницы: 11

Beacon Station BWS500

Бренд: Vaisala Страницы: 28

Бренд: A.H. Systems Страницы: 16

Бренд: SLX Страницы: 2

digiTop 27800RG

Бренд: SLX Страницы: 2

Бренд: SELFSAT Страницы: 50

Blitz BZ2000-ANT

Бренд: Ikan Страницы: 10

Бренд: Televes Страницы: 2

Бренд: Televes Страницы: 4

Бренд: PRO.SIS.TEL. Страницы: 6

Бренд: Paradigm Страницы: 20

Бренд: AmazonBasics Страницы: 28

Бренд: Label Italy Страницы: 10

Бренд: nedis Страницы: 52

Бренд: M2 Antenna Systems Страницы: 23

Бренд: M2 Antenna Systems Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды