Hy-Gain AV-18HT Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

background image

Figure 10

Tower Leg Clamp

Installation of 40-Meter Stub

NOTE: Each stub must be attached to a
separate tower leg. The 40-meter stub (now
being assembled) must be attached to the very
top of the tower section. See Figure 11.

Select the 7/16" x 68" tube and slip it into the
5/8" tube. Measure 90" for both Phone and
CW, as shown in Figure 11, then tighten the
compression clamp securely.

Select the 5/8" x 24" tube and install it on
tower using two leg clamps and two shorting
straps spaced 5 1/2" apart, as shown in Figure
11.

Slip a #6 tubing clamp onto the 5/8" tube.
Tighten slightly.

Place a 7/16" caplug on the top of the 40-meter
stub.

NOTE: The higher tubing clamp can be
loosened and the lower shorting strap hinged
to bring the 40-meter stub into a vertical
position.

«
...
11
12
13
14
15
...
»

Содержание AV-18HT





































Отзывы:

Нет отзывов

Похожие инструкции для AV-18HT

1.0 meter Back Pack Antenna

Бренд: Patriot Страницы: 12

airMax Sector AM-9M13-120

Бренд: Ubiquiti Страницы: 20

REMO BAS X3174 MIDI

Бренд: BAS Страницы: 2

Бренд: One for All Страницы: 2

NextG 007GTi PRO

Бренд: Datacom Страницы: 35

33691 ultra-flat digital amplified antenna

Бренд: GE Страницы: 10

Бренд: GE Страницы: 8

Бренд: GE Страницы: 4

Бренд: GE Страницы: 16

Бренд: GE Страницы: 12

Бренд: GE Страницы: 8

Ultra Pro Hover HD 250

Бренд: GE Страницы: 5

Бренд: GE Страницы: 5

Бренд: GE Страницы: 2

Бренд: GE Страницы: 10

Бренд: GE Страницы: 32

Бренд: GE Страницы: 36

Бренд: Silvercrest Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды