33692-2
Attic Mount Antenna Installation Guide
Thank you for purchasing the GE Attic Mount Antenna.
This antenna provides excellent reception of all digital TV
broadcast signals. This antenna is lightweight, easy to
assemble and simple to install. Make sure to position the
antenna so that it points to the TV towers in your area.
Frequency Range:
VHF 170 – 220 MHz
UHF 470 – 700 MHz
Horizontal Mount
“F” Type Connection
Impedance: 75 Ohm
Indoor use only
Required Supplies/Tools
•
Electric or cordless drill
•
1/8” drill bit (3.5mm)
•
Phillips head screwdriver
•
7/32” Socket (5.5 mm)
•
Coax Cable (not included)
M3X10mm Self-Tapping Screws 4PCS
M3X14mm Self-Tapping Screw 1PCS
M3X12mm Screws and Nuts 2PCS
M6X35mm Wood Screws 4PCS
Director A 2PCS
Director B 2PCS
UHF Dipoles C 2 PCS
Reflectors 12PCS
Reflector Bracket 4PCS
Antenna Main Boom 1PC
1
UHF ELEMENT INSTALLATION
2
VHF DIPOLES CONNECTION
3
VHF DIPOLES INSTALLTION
4
DISTRUBITING POINT OF VHF
DIPOLE INSTALLION
5
REFLECTOR BRACKETS
INSTALLATION
Attach UHF dipoles (C) with M3X12mm screws and nuts to both
sides of the antenna main boom (point C).
Attach the directors (A) & (B) with M3X10mm self-tapping
screws to both sides of the antenna main boom accordingly
(point A & B). Do not overtighten.
Connect the VHF dipoles together. Note: One will slide into
the other.
Attach the VHF dipoles to antenna main boom using the
M3X14mm self-tapping screw. Do not overtighten.
Attach the VHF Dipoles to the antenna main boom using the
nuts and washers pre-threaded on the antenna main boom.
Do not overtighten.
Attach two reflector brackets together as illustrated. Repeat
using the other two reflector brackets.
6
REFLECTORS INSTALLATION
7
REFLECTOR UNIT INSTALLATION
8
ATTIC INSTALLATION
Attach the reflectors (12 PCS) into the clasps on the reflector
brackets. Use the included reflector positioning guide to
properly align the reflector rods.
Attach the reflector unit to the VHF dipoles as shown above.
Select a location to install the mounting bracket in the attic (i.e. (1) rafter, (2) rafter
brace, or on the (3) attic decking). Note: For best reception, you will want to mount the
antenna as high as possible.
• Using a 1/8“ drill bit (3.5 mm), drill pilot holes where you want to install the mounting
bracket.
• Using the included M6X35mm screws, secure the mounting bracket to the surface.
• Attach the antenna to the mounting bracket using the mast.
• Point the antenna in the direction of the broadcast towers in your area.
• Connect the coax cable (not included) that runs from your device (TV, VCR, Cable Box,
etc.) to the antenna.
• Scan for your local TV channels following the instructions found in your
TV’s users manual
Helpful Tip:
To ensure you receive the maximum number of channels you may want to experiment
re-positioning the antenna and re-scanning for channels.
Reflector Positioning
Guide
VHF Dipoles
Mast
Mounting
Bracket
1
2
3
MADE IN CHINA
GE is a trademark of General Electric Company and is
under license by Jasco Products Company LLC, 10 E.
Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a limited-lifetime
warranty. Visit www.byjasco.com for warranty details.
Questions? Contact us at 1-800-654-8483 between
7:00AM—8:00PM CST.
YOU MUST PERFORM A CHANNEL
SCAN AFTER INSTALLATION.
SCAN
CHANNELS
Please refer to your TV
manual for scan instructions
or call TV manufacturer.
Questions? Contact us at
1-800-654-8483 between
7:00AM—8:00PM CST.
STOP
PLEASE DO NOT
RETURN TO STORE
