Hy-Gain AV-18HT Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 36

background image

The following Hy-Gain

verticals are well

adapted for the phasing arrangements
shown in this reports

MODEL 18HT-S HY-TOWER

The 18HT-S is a multi-band vertical antenna
with automatic band selection of 10-80 meters
by means of a unique stub decoupling system.
The Hy-Tower with a base loading coil
operates efficiently on 160 meters. The system
is foolproof, fed directly with a single 50 ohm
coax. No guys are required for the 24 feet high,
self-supporting tower. The top mast extends
the height to 50 feet. Two units make an ideal
phased array.

MODEL 18AVT/WB-S

The 18AVT/WB-S is a multi-band trap vertical

for 10 through 80 meters. It is completely fac-
tory

pre-tuned and exhibits an extremely low

angle

DX radiation pattern. It is easy to as-

semble, light weight which one man can install.
A single 50 ohm coaxial feedline is required.
Two or three 18AVT/WB-S's make an
excellent phased array.

A D D E N D U M

AMATEUR
PHASING

ENGINEERING REPORT

PHASED MULTI-BAND

VERTICALS for ADDITIONAL GAIN and
LOW ANGLE RADIATION

I N T R O D U C T I O N

«
...
25
26
27
28
29
...
»

Содержание AV-18HT





































Отзывы:

Нет отзывов

Похожие инструкции для AV-18HT

Бренд: L3 Страницы: 122

Sailor 900 VSAT

Бренд: COBHAM Страницы: 356

Бренд: M2 Antenna Systems Страницы: 3

Бренд: Labgear Страницы: 2

Бренд: M2 Antenna Systems Страницы: 8

Mantis Motorised MSAT ACU

Бренд: Vislink Страницы: 60

Yagi Y300 Series

Бренд: ZCG Страницы: 3

Бренд: Blake UK Страницы: 2

Бренд: Simrad Страницы: 176

Бренд: Hughes Страницы: 47

Бренд: Hy-Gain Страницы: 11

HughesNet AN8-074R

Бренд: Hughes Страницы: 56

Бренд: XIEGU Страницы: 7

Бренд: MELICONI Страницы: 32

Бренд: Kathrein Страницы: 26

Бренд: TDK Страницы: 2

FIND4/GPS D4 /SHK 4 -6-60-H Series

Бренд: Panorama Antennas Страницы: 12

Бренд: Sea Tel Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды