Raven SmarTrax Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 59

background image

5

Manual No. 016-5034-004

41

Cab Component Installation

FIGURE 4.

Node Installed

4.

Install the node mounting plate (P/N 107-0171-946) to the floor using the bolts removed from the machine’s
floor plate.

5.

Install the node (P/N 063-0173-228) on the node mounting plate using three 3/8”-16 nylon insert lock nuts
(P/N 312-4000-061).

Node Mounting Locations

FIGURE 5.

Node Mounting

When choosing the location for the SmarTrax node, consider the following points:

•

Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and
cable connection.

•

One of the six numbered direction arrows on the node must be oriented in the direction of forward vehicle
travel, one arrow pointing straight up, and two of the arrows parallel to the ground.

Note:

Make a note of the number of the arrow that is oriented in the direction of forward vehicle travel.
This number will be needed during the SmarTrax calibration process.

•

The node mounting location must not create tripping hazards.

•

Mount the node in a location where it will not be kicked or jarred during normal equipment operation.

•

The location must allow cable routing to avoid crimping or damaging the cables or the node connections.

Direction Arrows

Any two arrows must
be parallel with level
ground

Mounting Tabs

1

2

3

4

5

«
...
43
44
45
46
47
...
»

Содержание SmarTrax




























































Отзывы:

Нет отзывов

Похожие инструкции для SmarTrax

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 12

OPTYMA Plus OP-LPQM

Бренд: Danfoss Страницы: 8

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды